User manual PYLE PLVSHR6

[. . . ] 6 TFT LCD COLOR MONITOR OPERATING INSTRUCTIONS Before operating this set, please read these instructions completely LCD COLOR MONITOR OPERATING INSTRUCTIONS Congratulations for purchasing our video mobile multimedia products, before connecting, operating or adjusting this products, please read these instructions compactly to make your particular mobile multimedia products to best perform. 1. Do not repair it by yourself, if any trouble occurs, please immediately shuts it off and contact our company or local dealer. [. . . ] Special hints There may some blink dots in the screen, it's common phenomenon in active matrix display technology, but not a defect or trouble. 1. LCD COLOR MONITOR OPERATING INSTRUCTIONS Control and layout 1 2 3 4 5 6 7 8 Monitor (1) Adjust Increase (2) Menu (volume, brightness, color, contrast) (3) Adjust Decrease (4) Power on/off (5) Remote sensor (6) Audio out (earplug) (7) Audio / video in (8) Connecting cord Remote Control (1) Power on/off (2) Timer switch (3) Preference switch (4) Adjust Decrease (5) Mute (6) Memory (7) Picture up, down, left, right (8) Adjust Increase (9) Menu (volume, brightness, color, contrast) 1 2 4 6 7 5 8 9 3 2. LCD COLOR MONITOR OPERATING INSTRUCTIONS Installation Video output Audio input (red) Video input (yellow) Ground (black) DC 12V power input (red) Remote Control replacing batteries PULL OUT PUSH 1) Always use new batteries when replacing the old set. 2)Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 3)Battery replacement is necessary when remote control acts sporadically or stops operating this. 4)Do not drop, apply shock or step on the remote control 5)Do not spill water on the remote control 6) Do not place objects between the remote control and remote sensor. 7)Do not use remote controls for other equipments at the same time. 8)If the MONITOR does not operate even when operating the remote control from a close range, it is time to replace the batteries (use CR-2025), refer to the label on back of the basic control. 3. LCD COLOR MONITOR OPERATING INSTRUCTIONS Operating instructions 1)Press MODE button to select brightness, contrast and volume control, press +or - to adjust correspondent analog. 2) Press PP to select the preset analog. 3) Store your favorite When you have set desired brightness, color, contrast and Volume, press STORE, then press PP, the screen will display STORE PP, press STORE again, STORE in screen will turn into green, the moment analog has been stored, in the future to call out this setting return to the stored state, you only need to press PP button. Technical parameters LCD Drive Method: TFT Active Matrix Display Size: 6 Inch (diagonal) Aspect: 4:3 Display Format: 320 x RGB x 234 Number of Pixels: 224, 640 Video System Input: NTSC Back Light: High Brightness Type U Shaped CCFT Power Source: DC12V Current Consumption: 8W Dimensions: 113 x 156 x 26 (mm) w/o headrest kit Supplied accessories Wire cord Stand Remote control Headrest bracket Key 1 1 1 1 2 4. LCD COLOR MONITOR OPERATING INSTRUCTIONS Bracket 1 for mounting stand style purpose Bracket 2 for headrest frame style use purpose Mounting stand Key- for eject the monitor from headrest frame 5. Headrest frame LCD COLOR MONITOR OPERATING INSTRUCTIONS Use bracket 2 for headrest frame style Remove the bracket 2 from the monitor and install bracket 1 as folloes diagram for stand style use Bracket 1 for mounting stand style purpose Bracket 2 for headrest frame style use purpose Use bracket 1 for stand sytle 6. LCD COLOR MONITOR OPERATING INSTRUCTIONS Step of install headrest frame Setup work Remove the headrest and set it in an uncluttered work area. Take the appropriate precautions to ensure that it is not damaged during the installation. Measurements Push on the headliner with your fingers to make sure there are no obstructions that would hinder the installation. Use the paper template to mark the area to be cut. Cut the headrest Using an adjustable-depth blade, start your cut 1/4 inch inside one corner and cut diagonalyl across, stopping 1/4 inch in from the other corner, repeat the procedure for the other two corners. 7. LCD COLOR MONITOR OPERATING INSTRUCTIONS Remove form & obsturctions Carefully peel back the material. Set the adjustable blade to one inch depth and cut around the edges of the hole, staying 1/4 inch inside the edge. [. . . ] Before connecting the monitor, pull the connecting cable assembly through the headrest frame as shown in diagram. Place headrest frame into the opening and secure with correct fasteners. Install the headrest frame Pull the connecting cable through the center of the frame as shown in diagram, the secure with correct fasteners 8. LCD COLOR MONITOR OPERATING INSTRUCTIONS Preparing to insert monitor Adjust the bracket pin to 90 o, run the cable through the frame as diagram shown and connect it. Inert the monitor Push to insert the monitor to the headrest frame 9. LCD COLOR MONITOR OPERATING INSTRUCTIONS Swivel an angle Push up or down to adjust a suitable angle. Detachable Insert the key between the monitor and headrest frame gap and pull out to remove the monitor from the headrest frame. 10. [. . . ]