User manual PYLE PLVW8M

[. . . ] AV IN Jacks 4 LOCATION AND FUNCTION OF KEYS 1. (Power) Press button (1) to turn on/off the unit. POWER INDICATOR LIGHT When the system is on, the indicator light (2) will be illuminated. REMOTE SENSOR For option, the monitor can be supplied with the remote control according to the user's need. [. . . ] JACKS FOR EARPHONE There are two jacks (13) for earphone. You can connect earphone to any one of the jacks to receive sound signal. REMOTE Through the REMOTE jack (14), connect other VIDEO/AUDIO system to the monitor. Then you can control the VIDEO/AUDIO system by pointing the remote control directly to the remote sensor IR (3). DC 12V INPUT JACK Through this jack (15), provide DC 12V power supply to the unit. S-VIDEO JACK The jack (16) is used for S-VIDEO input. AV INPUT JACK The group of jacks (17) is used for VIDEO in, AUDIO R in and AUDIO L in. 6 TROUBLE SHOOTING Before going through the checklist, check wiring connection. If any of the problems persist after checklist has been made, consult your nearest service dealer. NO POWER Check if the power button on the front of the monitor is set to on. Check if the wires of DC power plug are properly connected. Check if there is power at the power supply outlet. THE PICTURE IS OVER DARK, OVER BRIGHT OR HAS NO COLOR: Press MENU button on the front of the unit, then press PICTURE+ button or PICTURE- button to increase or decrease the level of the corresponding item (BRIGHT, CONTRAST, COLOR or TINT) to proper value, then you can get an optimum picture effect. NO SOUND Check if the audio connections are properly connected. Check if the volume is minimum, and press the VOLUME+ button to increase the volume level. CAN'T RECEIVE TV SIGNAL OR THE PICTURE QUALITY IS POOR IN TV MODE: Please confirm if the antenna is connected to the antenna socket of the unit. Check if you have pulled out the antenna. Perhaps the signal of your position is too weak, and it can't receive any TV signal at all. BUTTONS DO NOT WORK Turn the unit off and on with the power button on the front of the unit. 7 BRACKET 3 (BKT3) 8 INSTALLATION HARDWARE (2) (3) (4) (5) (1) (6) (7) (8) (9) (a) (10) (b) (11) (12) (13) (14) (1) ASSY (Rotate combined bracket with Base A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 (2) Base B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 (3) Plastic tube ( 13mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 (4) Screw ( 3x10). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Before installing the tray, stick the smaller quadrate sponge (a) to the tray and stick the larger quadrate sponge (b) to the inner side of the fastener according to the arrow in the figure below, Doing this can ovoid scraping the steel ripple pipe. (10)Sponge (a) (10)Sponge (b) (6)Fastener (7)Fix bolt (9)Tray 11 INSTALL THE TV MONITOR OR THE CAMERA 1. INSTALL THE TV MONITOR Insert the clip screw (5) into the hole on the tray with the washer (a) (8) between the clip screw (5) and the tray. Then aim the clip screw to the hole on the bottom of the TV monitor and rotate the clip screw to fix the TV monitor to the tray. [. . . ]