User manual PYLE PWD531

[. . . ] SHOCK SENSOR PRE-WARNING: Siren chirps rapidly when shock sensor is trigger. If shock sensor is trigger for a second time within 10 seconds, the siren will sounds for 30 seconds. ALARM AND REMOTE STATER INTERACTION: Your remote engine start can be active even if the alarm system is armed or disarmed, arm or re-arm the alarm when engine is running via remote starting. REMOTE ENGINE START: Press button on the transmitter, siren will chirp once and parking light will turn on, within button again engine will start 2 seconds later. [. . . ] NOTE: You can exit a mode anytime by pressing the Button. REPLACE THE BATTERY OF YOUR TRANSMITTER: When transmitter battery low, icon will flashing at display and you hear beeps sound. Your two way transmitter is powered by an AAA 1. 5V alkaline battery. NOTE: When the battery weekends, operating range will be reduced and the back light will dim. Please check if the electrical outlets are mistakenly plugged Problem with the connection deactivating by transmitter after the Fuse of control module blow installation of the control module. Is the main module matched with the transmitter?Please check if there is something wrong with the 2. When the alarm is triggered the siren, check the connection between main unit and siren does not actives. See page 4 Is the LED plugged into the correct socket?This unit has easily-reversed lock/unlock output. Recheck page 4 to see if you have reverse these. Please check the connection see page 5. TWO WAY LCD TRANSMITTER OPERATION TRANSMITTER OPERATION Two Way Transmitter 2 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1. Engine running T WO - W AY MUTE START VIBRATION LOCK UNLOCK INTRODUCTION The newest technological are integrated in our Two Way Alarm and Remote Engine Start alarm system. They are fully programmable for your customers to have personalized security and comfort. 10PIN CONNECTION BROWN BROWN PURPLE YELLOW/ GREEN ORANGE WHITE YELLOW ORENGE/ BLACK WHITE/ BLACK YELLOW/ BLACK WIRING DESCRITION 4 PIN CONNECTION WHITE GREEN BLUE ORANGE WIRING DESCRITION Learning button WIRE CONNECTION GUIDE Blue Battery Starter Accessories Ignition Yellow Brown Red Parking light wire (12v positive output) connect to parking light wire Parking light wire (12v positive output) connect to parking light wire TACH wire (AC input) connect to TACH signal wire (coil or injector) Starter kill wire (500mA negative output) connect to starter kill relay. Lock Lock Lock NC COM NO (See page 5) (See page 5) (See page 5) (See page 5) (See page 5) (See page 5) Switched ignition input (12v positive input) connect to ignition wire. Hand brake wire (negative input) connect to switched side of hand brake switch. Door trigger negative input, connect to negative door switch. Brake wire (positive input) connect to the switched side of the brake pedal switch. ALARM The alarm integrated in the system is a fully programmable unit with multi zone protection such as shock sensor, starter kill output, control power locks and much more. Blac k Ground Pink White Siren WIRING DESCRITION 6PIN CONNECTION RED BLACK BLUE YELLOW BROWN PINK +12v constant wire (12v positive input) connect to a 12v constant, 30 A fuse built in. Ground wire, important connect to a ground. Accessories wire (12v positive output) connect to wire that controls the heater/air conditioning fan. Starter wire (12v positive output) connect to starter wire. [. . . ] Parking light will flash as 5 seconds press Arming the system will also enable the starter kill and unlock the door, if installed. PASSIVE ARMING: The system will automatically arm without door lock itself 30 seconds after the ignition has been turned OFF and the last door closed. DISARMING: Disarming the system will also disable the stater kill and unlock the door, if installed. SAFE REARMING: If you disarm the system by accident and you do not open any access (door ), it will rearm automatically after 30 seconds, unless the engine running. [. . . ]