User manual PYLE PYD1270

[. . . ] · Use the mixer only in well ventilated installations. · Handle the mixer gently and carefully-do not drop. · Keep the mixer away from dust and dirt. · Wipe occasionally with a damp cloth to keep it looking new. [. . . ] MIC1/MIC2/MIC3 & MIC4 Balanced XLR Input Connector For connecting a balanced low impedance microphone with XLR type plug. LINE 5/6, LINE 7/8, LINE 9/10, & LINE 11/12 BAL or UNBAL 1/4" (TRS) Input Jacks For connecting a balanced or unbalanced stereo line level sources. Use LEFT input jack only for each channel, if the source signal is mono. CTRL ROOM OUT Jacks To connect the mixer to a second receiver or amplifier powering speakers in the control room or in a remote location. HEADPHONES Jack Accepts the headphones with 1/4" plug. POWER ON Indicator MIC1/LINE 1, MIC2/LINE 2, MIC3/LINE 3, & MIC4/LINE 4 GAIN Control Lets you adjust the gain of the input source. MAIN OUT Jacks To connect the mixer to a receiver or amplifier. CH1, CH2, CH3, & CH4 Tone Controls (EQ) TAPE IN & OUT Jacks To connect the mixer to a tape deck for recording the mixed program and for auditioning mix playback from tape. TAPE TO MIX Switch Press to route the signal playback from tape to the MAIN mix bus. EFX TO CONTROL ROOM Switch Press to route the EFX SEND signal to the control room. DUAL LED DISPLAY METER Indicates the levels of left and right MAIN outputs. PHANTOM +48V DC Switch with Indicator Press to accept the use of condenser microphones. MASTER Level Control Lets you adjust the signal level of MAIN and TAPE outputs. EFX SEND Level Control Lets you adjust the EFFECTS signal level sent to the EFX SEND. CONTROL ROOM/PHONES Level Control Lets you adjust the signal level sent to the control room and headphones. TAPE TO CONTROL ROOM Switch Press to route the signal playback from tape to the control room. CH5/6, CH7/8, CH9/10, & CH11/12 BAL Control Lets you adjust the channel signal levels of left and right relative to each other before both signals are then sent to the MAIN mix bus. It allows you to balance the source in the stereo image. CH1, CH2, CH3, CH4, CH5/6, CH7/8, CH9/10, & CH11/12 EFX Control Lets you adjust the channel signal level sent to the external effect. CH1, CH2, CH3, & CH4 PEAK Indicator Indicates the channel signal is going into overload. CH1, CH2, CH3, & CH4 LO CUT Switch Press to eliminate unwanted low-frequency signal components. CH5/6, CH7/8, CH9/10, & CH11/12 GAIN Switch Press to increase the channel gain by +12dB. CH1, CH2, CH3, CH4, CH5/6, CH7/8, CH9/10, & CH11/12 LEVEL Control Lets you adjust the channel signal level sent to the MAIN mix bus. CH1, CH2, CH3, & CH4 PAN Control Lets you adjust the channel signal level feeding the L & R mix bus. Pyle Pro Mixer PYD6070/1270 Owner's Manual ­ 3 INSTALLATION, PYD6070 Mixers 4 ­ Pyle Pro Mixer PYD6070/1270 Owner's Manual INSTALLATION, PYD1270 Mixers Pyle Pro Mixer PYD6070/1270 Owner's Manual ­ 5 Mono Input Channel Controls CH1/CH2 For PYD6070 CH1/CH2/CH3/CH4 For PYD1270 MIC Each mono input channel comes with an XLR balanced microphone input connector and also offers a +48V PHANTOM switch to supply power for condenser microphones. Please mute the playback/PA loudspeakers system before switching on +48V PHANTOM power to prevent the switchon thumps being directed to the loudspeakers. Please connect the microphones before switching on the +48V PHANTOM power supply, do not connect microphones to the mixer as long as the phantom power supply is switched on. Wait for approximately one minute to get the system stabilized. EQ (HI/MID/LO) ALL the mono input channels has a 3-band equalizer, all bands provide up to 15dB of cut and boost, with a centre detent for OFF. The cut-off frequencies of HI and LO band are 10 kHz and 100 Hz respectively. The MID band is configured as a peak filter with a center frequency at 1 kHz . EFX It enable you to feed channel signal to the external effect. PAN It determines the amount of the channel signal feeding the left and right mix bus, to locate the source smoothly across the stereo image. [. . . ] This warranty is limited to the original retail purchaser of the mixer. Should the unit fail due to factory defects in material or workmanship, your unit will be repaired or replaced at the sole discretion of PYLE. To obtain warranty service, you must first call our Consumer Return Hotline at (718) 236-6948 to obtain a Return Authorization Number. # must appear on the outside of your package and on all paperwork relating to your return. [. . . ]