User manual PYLE PYD1930

[. . . ] Specifications PYD1910/1920/1930/1940/1950 Input Sensitivity/Impedance Mic 1-2 Phono 1-2 Line 1-6 Output Level Amp Zone Record Frequency Response S/N Ratio (at 1 kHz) Mic Phono Line Distortion Mic Phono Line 1. 5 mV/600 Ohms, bal/unbal 3. 0 mV/50K Ohms 150. 0 mV/27K Ohms 2. 0 V/10-kOhms 2. 0 V/10-kOhms 150mV/10-kOhms 20Hz ­ 20kHz +/- 3 dB >60 dB/1. 5mV input >70 dB/3. 0mV input >80 dB/150. 0 mV input 0. 20% 0. 05% 0. 03% Equalizer Control Frequencies Boost/Cut Range MIC Tone Control Treble Mid Bass 30, 60, 120, 250, 500 1K, 2K, 4K, 8K, and 16KHz +/- 10 dB from center 10kHz; +10/-30dB 1 kHz; +10/-30dB 100Hz; +10/-30dB Talkover Attenuation -16dB Echo Delay Time (PYD-1920/1940) 50mS-120mS 12 Seconds Sampling Length (PYD-1950) PYD-1910/PYD1920 PYD-1930/PYD-1940 PYD-1950 Dimensions, inches (mm) 19. 0 x 4. 13 x 9. 45 (482 x 105 x 240) pro series Power Source 120 VAC, 60Hz/230 VAC, 50 Hz All PYLE PRO products are carefully constructed and tested before shipment. Units purchased in the USA are warranted to be free of defects in material and workmanship for two (2) years from the date of purchase. This warranty is limited to the original retail purchaser of the mixer. Should the unit fail due to factory defects in material or workmanship, your unit will be repaired or replaced at the sole discretion of PYLE. [. . . ] Over a period of time, your ears adapt to a volume level and there is a temptation to increase it. Even though such an increase may not cause discomfort, it might still damage your hearing. Stereo Headphones Connecting the Mixer Outputs Output to an Amplifier To play the mixer's output signal through your speaker system (for events such as parties, dances, conferences, etc. ) connect an audio patch cord (not supplied) from the mixers AMP L and R jacks to your receiver amplifier's left and right input jacks. This mixer features two kinds of output jacks for you to choose from: RCA style and 1/4" type. DO NOT USE BOTH SIMULTANEOUSLY. Output to a Tape or Digital Audio Recorder To play the mixer's output signal through your speaker system (for events such as parties, dances, conferences, etc. ) connect an audio patch cord (not supplied) from the mixers REC L and R jacks to your receiver/amplifier's left and right input jacks. Zone Output To monitor the mixer output to a second set of speakers in the DJ booth (or in a remote location) connect an audio patch cord (not supplied) from the mixers ZONE L and R jacks to your secondary amplifier's left and right input jacks. CAUTION: In order to avoid sudden unpleasant sound output, adjust the output devices controls to these settings before you connect the mixer's output jacks to these devices' input jacks. Connecting the Lamp If you wish to intall a console lamp (not supplied), simply insert the plug end of an appropriate 12V/3W gooseneck style or similar lamp into the lamp socket provided in the upper right corner of the mixer control panel. Power is supplied to this lamp when the mixer power switch is turned on. 12V/3W lamp OUTPUT DEVICE Tape Deck Amplifier/Receiver CONTROL POWER POWER TONE SETTING OFF OFF FLAT 8 ­ Pyle Pro Mixer Owner's Manual Pyle Pro Mixer Owner's Manual ­ 9 Using the Mixer Controls Turning on the Mixer 1. Turn on the output amplifier and temporarily set its volume to the minimum setting. Turn on the audio input sources you wish to mix, and set them to play (or talk continuously into the microphone). To monitor the audio input sources so that you can decide when to mix in each input, see "Monitoring `Cueing' the Inputs. " 5. To mix the audio input sources so that you can play them through your amplifier system or record them on your tape deck, see "Mixing the Inputs. " Adding Equalization to the Mix You can further tailor the sound processed through the mixer to match your acoustic surroundings or suit your personal preferences by using the ten frequency sliders for each channel. To engage the equalization module, press the Equalization On/Off Switch. The LED next to the switch will be illuminated, indicated the EQ mode has been engaged. Each one of the sliding controls boosts or cuts the selected frequency by up to 12 dB. If you leave a slider at the center ("0") position, the corresponding frequency range for that stereo channel will be left unaffected ("flat"). Please note that in order to provide a smooth range of control, the frequency ranges overlap slightly. Therefore, for example, if you raise the level in the 2K range, the 1K and 4K ranges are also slightly affected. Adding External Effects to the Mix To connect a sound effect device such as an echo reverb or digital sampler processor, first connect the EFFECTS SEND jacks to the external device's AUDIO IN jacks using RCA type cables. Then connect the device's audio outputs to the EFFECTS RECEIVE jacks on the mixer. To activate the loop with which now has an outboard processor, press the Effects Switch. The effect devices are now in the audio chain. Be sure the device is ON. Monitoring ("Cueing") the Inputs 1. Set the CUE ASSIGN switch of the input source (MIC , CH1, CH2, CH3 or CH 4) you wish to monitor. Adjust the Headphone Level control to a comfortable listening level. The Headphone CUE/PGM control permits you to switch easily from listening to CUE material to the playing PROGRAM sound. You can also listen to both simultaneously by moving the Headphone CUE/PGM control to a point midway between the two ends. [. . . ] If you cannot solve the problem, contact a qualified technician for assistance. POSSIBLE SOLUTION · Check the AC connection. Make sure the AC outlet is "live. " · Check the power connection to the rest of the system (receiver/amplifier, etc. ) · Check the control setting · Check the connection between the mixer and the input source · Check that the turntable's ground wire (usually black or green) is fastened securely to the GROUND SCREW on the mixer input panel · Make sure there are no low level inputs connected to the LINE input jacks · Move the microphone further away from the output speakers, or use a directional microphone The built-in Echo effect is applied to the total mix. To turn on the Echo mode and activate the DELAY/REPEAT cycle, press the ECHO ON/OFF switch. To change the length of time a sound is repeated, increase of decrease the REPEAT control. [. . . ]