User manual PYRAMID 801

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual PYRAMID 801. We hope that this PYRAMID 801 user guide will be useful to you.

Lastmanuals help download the user guide PYRAMID 801.


Mode d'emploi PYRAMID 801
Download
Manual abstract: user guide PYRAMID 801

Detailed instructions for use are in the User's Guide.

[. . . ] If the input signal is mono, slide the Stereo/Mono/Bridged selector switch to MONO and the signal will be routed through both channels. If you wish to run the amplifier in bridged output mode, slide the switch to Bridged. Speaker connections You can connect 4 Ohm, 8 Ohm or 16 Ohm speakers to Channel 1 and/or Channel 2 of the amplifier. [. . . ] If you connect two pairs of speakers, be sure to follow these guidelines: · Speakers which are connected to the same channel are part of a pair, and must be of the same impedance. · Speakers connected to different channels are NOT part of a pair, and can be of different impedances. Prepare the speaker wire by removing about 1 inch of insulation from the end of the speaker wire you intend to connect to the amplifier. Then twist the exposed wire to secure all the wire strands. NOTE: Use 16-gauge speaker wire for lengths up to25 feet; 14-gauge wire for lengths over 25 feet. It is recommended that you use the shortest length of wire possible. Connect the speaker wires to the speaker's positive and negative terminals. NOTE: Most speaker terminals are either color-coded or have a mark that indicates the terminal's polarity. Push in the power switch to turn the amplifier on. Using the power LED meters The meter pointer position indicates the amplifier output power. For ease of reading in dark environments, the meter is illuminated. Using the Channel 1 and Channel 2 Output Level controls Rotate output level gain clockwise to increase, or counterclockwise to decrease the output power. To get the best performance with the least sound distortion, always adjust the output level gain so the meter's pointer does not continuously exceed the extreme right of the meter's scale. CAUTION: It is possible to overdrive the amplifier by setting output level gain too high, which may cause damage or failure. About the internal protect circuitry Special clip circuitry incorporated into your PYRAMID XPA amplifier's design protects the amplifier and speaker system from being damaged from overdriving power. Under normal conditions, the amplifier's clip indicator will flicker as the output power momentarily exceeds the level as set by the output level gain selector. Bridged Mode Operation This amplifier can operate in a mono bridged output mode, if your speakers can handle the following power output levels: XPA-100: XPA-200: XPA-300: 1000 watts 1600 watts 2000 watts CAUTION! [. . . ] About the internal protect circuitry Special clip circuitry incorporated into your PYRAMID XPA amplifier's design protects the amplifier and speaker system from being damaged from overdriving power. Under normal conditions, the amplifier's clip indicator will flicker as the output power momentarily exceeds the level as set by the output level gain selector. Bridged Mode Operation This amplifier can operate in a mono bridged output mode, if your speakers can handle the following power output levels: XPA-100: XPA-200: XPA-300: 1000 watts 1600 watts 2000 watts CAUTION!Do not use balanced and unbalanced inputs simultaneously!! As shown in the diagram below, connect the speaker's positive (+) to the amplifier's red speakers left (1/2) terminals and negative (-) to red speakers right (1/2) terminals. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PYRAMID 801

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual PYRAMID 801 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag