User manual QSC AUDIO WL115-SW

[. . . ] 1675 MacArthur Blvd. , Costa Mesa, CA, 92626 USA Main Number (714) 754-6175 Sales & Marketing (714) 957-7100 or toll free (USA only) (800) 854-4079 Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834 ILA Series Loudspeaker System User Manual WL2082-i full-range line array loudspeaker WL115-sw subwoofer line array loudspeaker FB2082-i array frame EB2082-i extension bar PB2082-i pull back bar GS115-sw ground stack kit *TD-000218-00* TD-000218-00 revD IMPORTANT SAFETY PRECAUTIONS Install in accordance with QSC Audio Product's instructions and under the supervision of a licensed Professional Engineer. WARNING! Before placing, installing, rigging, or suspending any speaker product, inspect all hardware, suspension, cabinets, transducers, brackets and associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could significantly reduce the strength of the installation, placement or array. Any such condition severely reduces the safety of the installation and should be immediately corrected. Use only hardware which is rated for the loading conditions of the installation and any possible short-term, unexpected overloading. [. . . ] The data presented is based upon the listed component weights: 6 Rigging the Installation Line Array (continued) Table 1: ILA Working Load Limits Component EB2082-i Extension Bar FB2082-i Array Frame PB2082-i Pull Back Bar WL2082-i Loudspeaker WL115-sw Loudspeaker M8 Shoulder Bolt1 M8 Ball-lock Pin1 M8 Locking Plate1 M12 Shoulder Bolt1 3/8" Fastener1 7/8" Fastener1 Weight 38 lb (17. 3 kg) 17 lb (7. 7 kg) 6 lb (2. 7 kg) 37 lb (16. 8 kg) 111 lb (50. 5 kg) not applicable not applicable not applicable not applicable not applicable not applicable 7:1 Design Factor 1714 lb (779. 2 kg) 740 lb (336. 4 kg) 423 lb (192. 2 kg) 634 lb (288. 3 kg) 740 lb (336. 4 kg) 1003 lb (455. 8 kg) 1810 lb (822. 7 kg) 1286 lb (584. 4 kg) 4744 lb (2156. 3 kg) 1943 lb (883. 4 kg) 8110 lb (3686. 4 kg) 10:1 Design Factor 1200 lb (545. 5 kg) 518 lb (235. 5 kg) 296 lb (134. 5 kg) 445 lb (201. 8 kg) 518 lb (235. 5 kg) 702 lb (319. 1 kg) 1267 lb (575. 9 kg) 900 lb (409. 1 kg) 3321 lb (1509. 4 kg) 1360 lb (618. 4 kg) 5677 lb (2580. 5 kg) 12:1 Design Factor 1000 lb (454. 5 kg) 432 lb (196. 2 kg) 247 lb (112. 1 kg) 371lb (168. 6 kg) 432 lb (196. 2 kg) 585 lb (265. 9 kg) 1056 lb (479. 9 kg) 750 lb (340. 9 kg) 2767 lb (1257. 8 kg) 1134 lb (515. 3 kg) 4731 lb (2150. 4 kg) 1- Working Load Limits are per fastener loaded in double shear. Data is for informational purposes only. Attaching WL2082-i to Array Frame Before beginning any installation, have your system designer configure the array with proper splay angles using QSC's EASE Focus (Array Calculator). All orientation of product is to be as viewed from the rear of the enclosure. NOTE: A washer should not be used when attaching the pull back bar. This will allow the pull back bar to pivot freely. Figure 9: Bolting order for EB2082-i Extension Bar rigging plates. Extension Bar The extension bar rigging plates can be moved, if required, by removing the two 7/8"mounting bolts, moving to the selected mounting location, and reattaching. Tightening torque is to be 100 lb-ft of torque (135. 6 N-m) Ease-Focus software's center-of-gravity calculator will provide a suitable point (or two points) for desired down-tilt. Attach the array frame to the extension bar rigging plates by centering the array frame member between the extension bar rigging plates and bolting together using the supplied 7/8" bolts. Attaching the WL115-sw to the Array Frame All orientation of product is to be as viewed from the rear of the enclosure. The QSC logo on the input plate will appear right side up when the enclosure is oriented properly. 1- Attach the array frame to the suspension structure using 3/4" (20 mm) shackle and appropriate sling, cable, etc. . . . For all four rigging straps: Using an 6mm hex wrench, remove the upper and lower rigging strap retaining bolts and loosen the two bolts in between. Pull the inner and outer straps to their outermost position; pull the center strap to its outermost position, and align the retaining bolt holes with the threaded inserts of the enclosure. Re-install the outermost rigging strap retaining bolts and tighten all four bolts on each strap to 13 lb-ft (17. 6 N-m). Figure 10: Extending the WL115-sw rigging straps. 8 Figure 11: WL115-sw attached to FB2082-i. Rigging the Installation Line Array (continued) 3- Lower the array frame onto the enclosure, carefully aligning the rigging straps, and attach the top enclosure to the array frame by installing the ball-lock pins or M8 bolts. Before lifting, ensure the audio connection to the enclosures are correct and functioning. NOTE: When attaching one WL115-sw to another WL115-sw, you must use the supplied ball-lock pins. This will allow for easier installation given the close spacing between consecutive WL115-sw enclosures. NOTE: When arraying two or more WL115-sw subwoofers, it is easiest to lay the enclosures on their backs, align and mate the rigging straps, and install the ball-lock pins. When installing the ball-lock pins, ensure full insertion and locking action. Figure 12: WL115-sw to WL115-sw rigging. Attaching the GS115-sw Ground Stack Rails to a WL115-sw 1- For all four rigging straps: Using an 6mm hex wrench, remove the upper and lower rigging strap retaining bolts and loosen the two bolts in between. Pull the inner and outer straps to their outermost position; pull the center strap to its outermost position, and align the retaining bolt holes with the threaded inserts of the enclosure. Re-install the outermost rigging strap retaining bolts and tighten all four bolts on each strap to 13 lb-ft (17. 6 N-m). 2- Position a GS115-sw Ground Stack rail between the rigging straps on the right and one to the outside of the rigging straps on the left side of the loudspeaker. 3- Attach the rail to the rigging strap by inserting the cap-head shoulder bolt with washer through the mated components and threading the lock nut (nylock) on the inside edge of the assembly. [. . . ] The BI AMP HORIZONTAL SHADING switch will select which transducer is shaded. TRI AMP: Shading network is NOT applied (shading must be provided by upstream signal processing). The Bi Amp Mode Horizontal Shading selector switch is not functional in tri amp mode. Connect to the Speakon as shown for tri amp. Figure 17: MODE selection switch. Figure 18: BI AMP MODE HORIZONTAL SHADING selection switch. BI AMP MODE HORIZONTAL SHADING Selection Switch The BI AMP MODE HORIZONTAL SHADING selection switch is only functional in bi amp mode. [. . . ]