User manual QTEK 1010

[. . . ] Pocket PC Phone 2 Pocket PC Phone User Manual Please Read Before Proceeding THIS DEVICE IS NOT CHARGED WHEN YOU TAKE IT OUT OF THE BOX. Contents DO NOT REMOVE THE BATTERY PACK WHEN THE DEVICE IS CHARGING. WHEN INSERTING YOUR SIM CARD, MAKE SURE THE DEVICE IS POWERED OFF, AND THAT THE SIM CARD SNAPS INTO THE SOCKET. YOUR WARRANTY IS INVALIDATED IF YOU OPEN OR TAMPER WITH THE DEVICE'S OUTER CASING. EXPLOSIVE ATMOSPHERES When in any area with a potentially explosive atmosphere or where flammable materials exist, the product should be turned off and you should obey all signs and instructions. [. . . ] If you do not have access to broadband Internet, consult with your ADSL or DSL Internet service provider before attempting to run this utility. NOTE: The availability and range of your device's WLAN signals may depend on the number, thickness, and location of walls, ceilings, or other objects that the wireless signal must pass through. Checking for a Wireless LAN Signal Before starting WLAN Manager, verify that your device has access to a Wireless LAN channel signal. To check the current wireless connection status, open the Today screen or the Wireless Manager screen, as follows: Today screen: If your Pocket PC Phone has detected a WLAN network connection, a "W" icon will be shown at the right side of the Title Bar (top of screen). The WLAN and Bluetooth icons are shown at the right side of the Command Bar (bottom of screen). Wireless Manager screen: Getting Connected Select Wireless Manager from the Start menu, or from the Programs group (Start menu > Programs). The current ON/OFF status for each specific wireless channel will be indicated in the Wireless Manager screen. If your Pocket PC Phone is receiving WLAN signals, the message "WiFi connection is in use" will display under the WLAN button. NOTE: WLAN (WiFi) is the default wireless channel setting for your device. GPRS will be launched if no WiFi signal is detected. Pocket PC Phone User Manual 103 Invoking WLAN Manager To open the Wireless LAN Manager screen, select Start menu > Settings > Connections > WLAN. Or, if you have the Wireless Manager screen open (mentioned above), you can tap the WLAN icon in the Toolbar at the bottom of the Wireless Manager screen. Using WLAN Manager The WLAN Manager application consists of three screens: Main, Settings, and LEAP. By default, the Main screen is displayed. Tap the Settings tab or the LEAP tab near the bottom of the screen to open those screens. In the Command Bar, there are two icons. The leftmost icon, Network Cards, is a shortcut to the Start menu > Settings > Connections tab > Network Cards utility. Tapping the rightmost icon, Wireless Manager, will switch to the Wireless Manager utility. (Access the on-line Help from those screens if you need information about their usage. ) Getting Connected NOTE: Tapping the Network Cards icon mentioned above will open the Configure Wireless Networks screen. This screen lists the available APs and lets you add a new one. Note that if you are currently connected to the AP, and a correct IP address has been obtained, the status will be shown as "Connecting" initially. In order to re-paint the status as "Connected, " simply refresh by leaving the screen and then coming back to it again. 104 Pocket PC Phone User Manual Main screen The Main screen displays data related to the current configuration, and the quality of the WLAN signal, for your reference. Fields in this screen are: Status This field displays messages that inform you of the current connection status. Examples: "Connected to network, " "Not connected to network, " "Scanning network. . . ". SSID SSID is Service Set Identifier, a unique name that identifies a network. All devices on a network must share the same SSID name in order to communicate on the network. [. . . ] Tap Start > Settings > the System tab > Screen > Align Screen. n Inaccurate response to stylus taps. Troubleshooting n Pocket PC does not recognize handwriting. For your Pocket PC to recognize your handwriting input with the stylus, you need to use Transcriber writing. To learn how to write in Transcriber, see Chapter 2. ActiveSync Problems Problem n ActiveSync operation cannot be performed or connected. 1 2 3 Solution Make sure the ActiveSync cradle/cable is connected securely. Make sure you have installed the ActiveSync software included on the Companion CD. [. . . ]