User manual QUANTUM 6211221V6R0

[. . . ] ACL 4/52 Automated Tape Library for DLT Cartridges Facilities Planning and Installation Guide 6211221-06 Ver. 0 ACL 4/52 Facilities Planning and Installation Guide, 6211221-06, Ver. provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. may revise this publication from time to time without notice. [. . . ] 2 Gently slide the horizontal carriage toward the front of the library. 3 Remove the top and bottom horizontal carriage foam blocks. 4 Gently raise the vertical carriage and remove the vertical carriage foam block. 5 Save all the blocks for future use. ACL 4/52 Facilities Planning and Installation Guide 13 Chapter 2 Unpacking the Library Removing Internal Packing and Inserting Tape Cartridges Figure 12 Removing the Foam Blocks Extension Axis Top Horizontal Carriage Foam Block Vertical Carriage Bottom Horizontal Carriage Foam Block Vertical Carriage Foam Block Horizontal Carriage ESD Ground Jack (On Lower Panel Tab) TA00136a To Load Available Tape Cartridges 2 If the customer has tape cartridges available for loading at this time, it is best to do this while the side panel is removed. You can insert up to 48 cartridges directly into empty bins in the fixed storage array. Figure 13 shows how cartridges should be oriented before insertion into a bin. Figure 13 Tape Cartridge Orentation To the Bin Cartridge Bar Code Label DLT Cartridge 14 ACL 4/52 Facilities Planning and Installation Guide Chapter 2 Unpacking the Library Removing Internal Packing and Inserting Tape Cartridges Do not be concerned if the customer does not have all the cartridges needed to fill the library. Additional cartridges can be added after installation using the load port. For more information about this procedure, refer to the Enterprise Tape Library 4/1800 Operator's Guide. Note: Whenever possible, try to fill the library completely with properly labeled tape cartridges. A full library of labeled cartridges takes much less time to inventory than a partially filled library or a library filled with unlabeled cartridges. Reinstalling the Left Cosmetic Panel 2 To reinstall the left cosmetic panel: 1 Rest the top lip of the left panel on top of the library frame. 2 Push the panel toward the front of the library and insert the frame buckles into the retention tabs. 3 At the back of the library, insert the tighten the three screws that secure the left panel to the back of the library frame. ACL 4/52 Facilities Planning and Installation Guide 15 Chapter 2 Unpacking the Library Storing the Packing Materials Storing the Packing Materials 2 After unpacking the library and removing internal packing materials, you should store all materials for future use. Follow this procedure: 1 Raise the ramp and rest it on top of the pallet. 3 Store the box, foam cap, pallet, and all packing materials for future use. 16 ACL 4/52 Facilities Planning and Installation Guide Chapter 2 Unpacking the Library Packing the Library for Shipment Packing the Library for Shipment 2 If it becomes necessary to ship the library, you must repack it in its original shipping materials as explained in this section. The following are the main steps in this procedure: · · · · · · · Removing power from the library Removing the left cosmetic panel Unloading the library Installing the internal packing materials Replacing the cosmetic panels Moving the library onto the shipping pallet Securing the library to the pallet Removing Power from 2 the Library To remove power from the library: 1 If necessary, unload and eject any tapes in the tape drives. 2 Turn off the library by setting the power switch to the O (off) position. 3 Disconnect all SCSI cables from the back of the library. Leave the power cord connected. Caution: Do not disconnect the power cord from the library or the grounded power source until instructed to do so. While plugged in, the power cord grounds the library chassis and helps to prevent electrostatic discharge (ESD) damage. Removing the Left Cosmetic Panel To remove the left cosmetic panel: 2 1 At the back of the library, remove the three screws that secure the left side panel to the library frame. 2 Pull the panel toward the back of the library (to disengage the retention tabs) and then move the panel from the library frame (see figure 10 on page 12). Carefully set the left panel aside. ACL 4/52 Facilities Planning and Installation Guide 17 Chapter 2 Unpacking the Library Packing the Library for Shipment Unloading the Library 2 To unload the library: 1 Remove all tapes from the fixed storage bins. To do this, grasp the exposed end of each tape and lift it out of the bin. [. . . ] Press (to release) the control panel STANDBY button and verify that the library completes the initialization sequence, and "System On-line" is displayed in the SDA. ACL 4/52 Facilities Planning and Installation Guide 43 Appendix B Supplemental Installation Procedures Turning the Interior Light On/Off Figure A-2: Turning the Interior Light On/Off Power Switch (Shown in Off Position) Interior Light Front Door (Opens to Right) TA00038d 44 ACL 4/52 Facilities Planning and Installation Guide Appendix B Supplemental Installation Procedures Turning the Interior Light On/Off ACL 4/52 Facilities Planning and Installation Guide 45 Appendix B Supplemental Installation Procedures Turning the Interior Light On/Off 46 ACL 4/52 Facilities Planning and Installation Guide Glossary Glossary A actuators Robotic components that move inside the library to manipulate cartridges. These include the gripper, extension axis, vertical and horizontal axes. automated tape library A robotic storage and retrieval system for DLT tape cartridges. B bar code label The identification label on DLT tape cartridges. bar code scanner A device that is mounted on the extension axis that reads the cartridge bar code labels. C calibration The software measurements and configuration required for successful operation of the library. [. . . ]