User manual QUANTUM 642100206A01

[. . . ] Quantum ATL M1500 Unpacking Instructions Introduction Removing the Library from the Shipping Carton Removing the Remaining Packing Materials Checking the Contents 3 3 5 10 Document 6421002-06 A01, July 2003 1 Quantum ATL M1500 Unpacking Instructions Document 6421002-06 A01 July 2003 2 6207947-04fN 5 Quantum ATL M1500 Unpacking Instructions Document 6421002-06 A01 July 2003 Introduction This document explains how to unpack a Quantum ATL M1500. The unpacking procedure consists of the following major steps: · · · Removing the library from the shipping carton Removing the remaining packing materials Checking the contents 0 Removing the Library from the Shipping Carton To unpack the library: Note: 0 Be careful not to damage the packaging materials while unpacking the library. [. . . ] At least two people are required to move the library. Lift the library by its sides, not by the front bezel. Caution: 7 Place the wrapped library on a table or desk. 4 Removing the Library from the Shipping Carton Quantum ATL M1500 Unpacking Instructions Document 6421002-06 A01 July 2003 Removing the Remaining Packing Materials Now that you have removed the library from its shipping carton, remove the remaining packing materials from the library: 1 Remove the antistatic sheet from the library as follows: a b c d 0 Cut the tape strips securing the sheet. With the help of a second person, lift the library up off of the antistatic sheet. Place the library on the table or desk next to the antistatic sheet. Save the antistatic sheet for possible future use. 2 At the back of the library, remove the handle protection pad. Caution: The library is equipped with a StackLink cover plate. Do not remove the StackLink cover plate if the library is a stand-alone unit. 3 If the library will be installed in a rack with a StackLink mechanism, remove the StackLink cover plate from the back of the library using a no. or 250 mm long) (see figure 2). Figure 2 Removing the Cover Plate 4 Put on an antistatic wrist strap and clip it to the antistatic stud on the back of the library (near the power supply). Removing the Remaining Packing Materials 5 Quantum ATL M1500 Unpacking Instructions Document 6421002-06 A01 July 2003 5 Push the button next to the right magazine access door (see figure 3). The right magazine access door opens. Figure 3 Opening the Right Magazine Access Door Right magazine access door Button 6 Grasping the handle at the front of the magazine, slide it forward and out of the library (see figure 4). Figure 4 Removing the Magazine Magazine 7 Push the button next to the left magazine access door (see figure 5). The left magazine access door opens. 6 Removing the Remaining Packing Materials Quantum ATL M1500 Unpacking Instructions Document 6421002-06 A01 July 2003 Figure 5 Opening the Left Magazine Access Door Button Left magazine access door 8 Using a slender object such as a pen, press and hold the magazine release button (see figure 6). Figure 6 Magazine Release Button, Left Side Only 9 Grasping the handle at the front of the left magazine, slide it forward and out of the library. 10 Use the following steps to remove the two foam pads that stabilize and support the X-Y tray inside the library (see figure 7): a b Grasp the tape that secures each foam pad. Lift the tape and foam pad up and pull towards the door. Avoid touching the printed circuit board and its ribbon cable connector. [. . . ] Refer to the Quantum ATL M-Series Installation Guide (6423001) for installation instructions. Checking the Contents 0 Compare the contents of the shipping carton and the accessories kit with the items listed on the label on the outside of the shipping carton. If any items are missing or damaged, contact your authorized reseller. Note: The tape drives and media are sent separately from the library. 10 Checking the Contents [. . . ]