User manual QUANTUM 6421018V2R0

[. . . ] Quantum ATL M1500 User's Guide Addendum -- FC310 Router Option Introduction 3 Fibre Channel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FC310 Router Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Key to Successful Configuration of the FC310 Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FC310 Router Option Configuration 4 FC310 Configuration Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Upgrading the FC310 Prism Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Commonly Used FC310 Services Software Commands for the ATL M1500 Library FC310 Services Software Commands 11 13 FC310 Service Software Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Command Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 List of Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Command Listing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Document 6421018-02, Ver. 0, September 2002 1 Quantum ATL M1500 User's Guide Addendum - FC310 Router Option Document 6421018-02, Ver. 0 September 2002 2 6207947-04fN 10 Quantum ATL M1500 User's Guide Addendum - FC310 Router Option Document 6421018-02, Ver. 0 September 2002 Introduction 0 The ATL M1500 tape library can contain up to two tape drives and up to 21 DLT/SDLT cartridges and 25 LTO cartridge. [. . . ] The automap command executes. 2 When the ready prompt appears, type saveconfiguration and press <Enter>. 3 When the ready prompt appears, type firmwarerestart and press <Enter>. 10 FC310 Router Option Configuration Quantum ATL M1500 User's Guide Addendum - FC310 Router Option Document 6421018-02, Ver. 0 September 2002 Figure 5 Automap Screen Commonly Used FC310 Services Software Commands 0 for the ATL M1500 Library The FC310 Services Software resides on each FC310 Router board. This software configures the router for use in the Quantum ATL M1500 library through a Command Line Interface (CLI) that is compatible with any PC and a terminal emulation program (such as HyperTerminal or ProComm). For more information on additional commands, syntax, and usage, see FC310 Services Software Commands on page 13. Commonly Used FC310 Services Software Commands for the ATL M1500 Library 11 Quantum ATL M1500 User's Guide Addendum - FC310 Router Option Document 6421018-02, Ver. 0 September 2002 Table 2 Commonly Used FC310 Services Commands Command RouteDisplay Description List the currently mapped Fibre Channel-to-SCSI routes. Default Syntax routedisplay routedisplay [fp] routedisplay [online | offline] routedisplay [fp [fl] ] routedisplay [fp [online | offline] ] SerialPortBaudRate Set the baud rate for the FC310 serial port (2400, 9600, 19200, 38400, 57600, or 115200). Turn on or off the echoing of keyboard input. Transfer a firmware image or NVRAM parameter file to or from the router using ZMODEM file transfer protocol. Displays version numbers and other product information for key components within the FC310. When the optional command name is present, detailed command-specific information is displayed. If a firmware restart is required to make the change, the user is prompted to confirm the restart. Several non-immediate commands require a SaveConfiguration before their modified parameters take effect. When such a command is executed an asterisk appears next to the command line prompt. FC310 Services Software Commands 13 Quantum ATL M1500 User's Guide Addendum - FC310 Router Option Document 6421018-02, Ver. 0 September 2002 Command Syntax 0 The following is a list of syntax used to describe command lines: · · · [ ] indicates required entry < > indicates optional entry | indicates choose one entry List of Abbreviations 0 The following is a list of abbreviations used to describe command lines: · · · · · fpFibre Channel port number (0 - 2) flFibre Channel LUN (0 - 31) sbSCSI bus number (0 - 3) stSCSI target ID (1 - 15) sl SCSI LUN (0 - 7) Command Listing 0 A list of the currently available FC310 Services Software commands is shown in table 2. Table 3 Most Common FC310 Services Commands Command FcConnMode Description Set the connection mode for the FC310 to arbitrated loop or pointto-point. Applies to all three Fibre Channel ports on each board. Turn on or off the FC-AL arbitration fairness. Applies to all three Fibre Channel ports on each board. Specify the maximum number of payload bytes in a Fibre Channel frame. If the frame length is not specified, the current frame length is displayed. Default loop Syntax set fcconnmode [loop | ptp] get fcconnmode FcFairArb enabled set fcfairarb [enabled | disabled] get fcfairarb FcFrameLength 2048 bytes set fcframelength [512 | 1024 | 2048] get fcframelength 14 FC310 Services Software Commands Quantum ATL M1500 User's Guide Addendum - FC310 Router Option Document 6421018-02, Ver. 0 September 2002 Command FcHard Description Enable or disable Fibre Channel hard address assignment. Under soft addressing the FC310 loop address is assigned during loop initialization. Set the value used as the FC-AL hard address. Default hard Syntax set fchard [enabled | disabled] get fchard FcHardAddress port 0 = 3 set fchardaddress [fp [address]] get fchardaddress [fp] FcSCSIBusyStatus Specify the SCSI status value returned when the FC310 is unable to accept a SCSI command due to a temporary lack of internal resources. [. . . ] The mask is a byte value with the following bit patterns corresponding to the currently supported reporting levels: 0x01 Info; general information 0x02 Warning; unexpected situation/condition 0x04 Critical; operation limited/curtailed 0x08 Failure; hard failure 0x10 Other; otherwise not categorized 0x20 Debug; tracking events To display events from several different reporting levels, use a mask value equal to the logical OR of the corresponding reporting levels. To display events for all reporting levels enter the value 3Fh for the mask. (status) switch: has the following two values which correspond to the status of the events to be displayed: all All events, regardless of their status values are displayed. ngood Only events with a status other than good are displayed. [. . . ]