User manual QUANTUM 6444602 03 A01

[. . . ] The required wall outlet for the United States and Canada is rated at 250V 20A (see figure 4). Figure 4 Wall Outlet Ground Line y Line x Wall outlet: NEMA L6-20R rated 250V 20A Two dedicated wall outlets and a 20 amp circuit breaker are required to provide power to the PX720 library. Outside North America, replace the supplied power cord with a harmonized 3 x 1. 5 mm2 power cord that is approved by the country where used, and install the appropriate wall outlet. More information on the electrical requirements is provided in the Quantum PX720 Pre-Installation Site Survey Instructions. Caution: The PX720 library must be connected to a grounded electrical outlet. Selecting an Installation Location 5 Quantum PX720 Unpacking and Installation Instructions Document 6444602-03 A01 August 2004 Environmental Conditions The installation site must have the following environmental conditions: 0 · · · Humidity: 20%-80% non-condensing Temperature: 15°C-32°C (59°F-90°F) Altitude: sea level to 3048 meters (10, 000 feet) These environmental conditions apply when the library is in operation. [. . . ] 10 Cut the tape securing the ramp against the library. hex head bolts, lock washers, and flat washers removed in step 7 to secure the ramp to the pallet (see figure 10). Figure 10 Lowering the Ramp Ramp Hex head bolts Positioning the Library0 To position the library: 1 Map out a route to the installation site (see the Quantum PX720 PreInstallation Site Survey Instructions). 2 Remove the four restraining bolts securing the PX720 to the shipping pallet (see figure 11) using a 3/4 in open-end wrench. Unpacking the Library 11 Quantum PX720 Unpacking and Installation Instructions Document 6444602-03 A01 August 2004 Figure 11 Removing the Restraining Bolts Bolts Bolts 3 Raise the leveling feet (see figure 12). Figure 12 Raising the Leveling Feet Leveling feet in raised position 4 Inspect the library for any damage that may have occurred during shipment. 12 Unpacking the Library Quantum PX720 Unpacking and Installation Instructions Document 6444602-03 A01 August 2004 5 Carefully roll the library down the ramp (see figure 13). Warning: The Quantum PX720 with 20 tape drives weighs 1350 pounds (612 kg). Two people are required to move and install the library. Figure 13 Rolling the Library Down the Ramp 6 Guide the library to its final installation site. 8 Store the five spare screws in the robot shipping restraint as shown in figure 19. 9 Using the remaining two screws, secure the shipping restraints in the library as shown in figure 19. 18 Unpacking the Library Quantum PX720 Unpacking and Installation Instructions Document 6444602-03 A01 August 2004 Figure 19 Storing the Shipping Restraints Shipping restraints in storage position Spare screws Shipping restraints 10 From the back of the library, remove the two nuts securing the counter weight shipping restraint to the back wall with a 7/16 inch wrench (see figure 20). Figure 20 Removing the Counter Weight Shipping Restraint Shipping restraint Nuts 11 Reverse the counter weight shipping restraint and reinstall on the back wall of the library using the two nuts previously removed in step 10 (see figure 21). Unpacking the Library 19 Quantum PX720 Unpacking and Installation Instructions Document 6444602-03 A01 August 2004 Figure 21 Storing the Counter Weight Shipping Restraint Shipping restraint Nuts 12 Remove the six panel shipping restraints (three on each side) with a 7/16 in. Note: To access the lower panel restraints, you must manually trip the load port latching mechanism to release the load port. The load port latching mechanism is located between the load port and the outer skin of the panel (see below). Using the tip of a screw driver, lift the latch up to release the load port. Latch Screwdriver 20 Unpacking the Library Quantum PX720 Unpacking and Installation Instructions Document 6444602-03 A01 August 2004 Figure 22 Removing the Panel Shipping Restraints Upper shipping restraint Upper shipping restraint Load port latching mechanism Middle shipping restraint Lower shipping restraint Middle shipping restraint Lower shipping restraint Panels shown outside of library for clarity 13 Store the panel shipping restraint hardware (three sets on each side) on the lower cabinet frame as shown in figure 23. Unpacking the Library 21 Quantum PX720 Unpacking and Installation Instructions Document 6444602-03 A01 August 2004 Figure 23 Panel Shipping Restraints Storage Locations Panel restraint storage locations Left storage position shown Storing the Shipping Materials 0 To store the shipping and packaging materials for future use: 1 Detach the ramp and place on top of the pallet. 3 Place the shipping bag, foam cap, screws, internal library frame restraint, and other packaging materials on the pallet. 5 Place the cardboard box on top of the packaging materials on the pallet. 6 Secure the pallet, packaging materials, and cardboard box for future use. Leveling the Library 0 To level the library: 1 Rotate each foot of the library until it makes contact with the floor. 2 Rotate each foot an additional 1/4 turn with the open-end wrench to begin raising the library. 3 Center a carpenter's level on the top front edge of the library. If the front of the library is level, proceed to step 6. If it is not level: a b Determine which side of the library is low. Adjust the leveling foot on the low side of the library by rotating the leveling foot with the open-end wrench. 22 Unpacking the Library Quantum PX720 Unpacking and Installation Instructions Document 6444602-03 A01 August 2004 5 Repeat step 4 until the front is level. 6 Repeat step 3 and step 4 for the left edge, back edge, and right edge of the library. 8 If necessary, repeat step 3 and step 4 until all four top edges of the library are level. The unpacking is complete. Installing the Quantum PX720 Library Installing the Quantum PX720 library consists of the following steps: · Cabling the Quantum PX720 · · · · · Connecting the Cluster Controller Ethernet Cables Cabling a SCSI PX720 Library Cabling a Fibre Channel PX720 Library 0 Loading the Tape Cartridges Initial Configuration Cabling the Quantum PX720 0 After the Quantum PX720 is in its final location, the tape drives and robotics controller must be connected to the backup host system(s). The cluster controllers must also be connected with Ethernet cables. [. . . ] When prompted, re-enter the password to confirm. To enable autoclean, use the up and down arrows to select Autoclean and press Select. To enable the left load port, use the up and down arrows to select Left Load Port (16) and press Select. To enable the right load port, use the up and down arrows to select Right Load Port (32) and press Select. · · · 7 When you are finished viewing/editing the setup information, press Back twice to return to the Home screen. [. . . ]