User manual QUANTUM 6473025V4R0

[. . . ] MC350 Prism Management Card User's Guide 6473025-04 Ver. 0 MC350 Prism Management Card User's Guide, 6473025-04, Ver. Quantum Corporation provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice. [. . . ] The temperature displays in degrees Fahrenheit and Celsius for each fan module (which can contain one or two fans, depending on your system configuration). Cartridge status of the gripper Cartridge status of the bins located in the door Cartridge status of the bins located at the rear of the library Each drive may be accessed for more detailed information. If a drive appears as black, there is no drive present in that slot. If the drive appears with a red background, there is a problem with that drive or it may require cleaning. Status of the AC power distribution sources Status of the DC power distribution sources Voltage status of the library Fans/Temperatures Main Robot Door Rear Bins Drives AC Power Distribution DC Power Distribution System Voltages 56 MC350 Prism Management Card User's Guide Chapter 5 ALERT Library Management Library Status Viewing Drive Element Information 5 To view the element status for a particular tape drive, from the Library Status page, click on the desired tape drive in the Drives section. The management frame displays the read-only Element Information page (see figure 19) with information on a specific drive (see table 10). Note: If you add or remove drives from the library, the number of drives or bins on the Library Status page may differ from the number of drives shown on the Library Configuration page. To correct this, you must revert the library to a default configuration. The default configuration contains the factory defaults and settings. This includes, but is not limited to, partition settings and Fibre Channel port mapping. If further information is required, contact the Quantum Customer Support department. Figure 19 Element Information MC350 Prism Management Card User's Guide 57 Chapter 5 ALERT Library Management Library Status Table 10 Element Information Fields Field Tape Drive Tape Model Tape Drive Revision Tape Drive Serial Number Drive SCSI ID Media Type Tape Drive Raw Status Tape Drive Status Byte 3 Tape Drive Status Byte 7 OK to Load Tape Alert Capable Tape Motion Description Displays the tape drive number selected Displays the tape drive type (i. e. , DLT8000) Displays the firmware revision of the selected tape drive Displays the serial number for the selected tape drive Displays the SCSI ID for the selected tape drive Displays the type of cartridge in the selected tape drive (for example, DLT8000) Displays information on the tape drive source code Displays detailed information for the FSE to help diagnose possible problems Displays detailed information for the FSE to help diagnose possible problems Displays readiness status of the tape drive to receive a cartridge, Yes or No Displays detailed information for the FSE to help diagnose possible problems Displays tape drive status: · Idle · Cleaning · Receiving firmware upload · Unloading · Loading Each of the 12 bytes of the tape drive status code is assigned a specific function. Certain bytes are necessary for FSEs to diagnose problems. 58 MC350 Prism Management Card User's Guide Chapter 5 ALERT Library Management Library Configuration Field Cleaning Requested Partition Description Displays whether cleaning has been enabled Displays the partition in which the selected tape drive belongs Each of the 12 bytes of the tape drive status code is assigned a specific function. Certain bytes are necessary for FSEs to diagnose problems. Library Configuration The Library Configuration page allows you to view and configure the library settings. The settings to configure are: · · · SCSI ID -- sets the SCSI ID of the library (represents the robotic 5 controller) Number of Drives -- specifies the number of drives Number of BarCode Retries -- determined how many retries the library will attempt to read the barcode of a tape cartridge during inventory. Valid values range from 1 to 8 · · Online on Power Up -- determines whether the library should be brought online after powering up No Barcodes -- enables or disables the barcode read feature. If the barcode read feature is enabled, the firmware returns are displayed. Note that an inventory is required in order to display the firmware returns. If the barcode is disabled, data retrieved via SCSI has the barcode blanked out even if the firmware returns valid barcodes. However, barcodes continue to appear in the Library Status page of a slave library in a multiple frame environment. MC350 Prism Management Card User's Guide 59 Chapter 5 ALERT Library Management Library Configuration · Auto Load -- determines whether the library will automatically put the tape cartridge into a free bin whenever a tape cartridge is detected in the load port Note: Do not use the Auto Load feature with partitioning. If partitioning is configured, the tape cartridge could be placed into a bin that belongs to a different partition. You would be required to move the tape cartridge into the correct partition after Auto Load finishes. · · Auto Drive Unload -- determines whether a tape cartridge can be automatically unloaded from a drive Auto Inventory -- determines whether the library should automatically inventory whenever an event such as power up or door close takes place Temperature Detection -- enables or disables display of temperature · · · sensor readings on the Library's LCD panel Auto Clean -- determines whether the library should automatically clean the tape drives as necessary Drive Configuration -- configures a drive's SCSI ID Accessing Library Configuration 5 To view or edit the library configuration: 1 In the navigation frame of the ALERT Library Management page, click Library Configuration. The management frame displays the Library Configuration page (see figure 20). 60 MC350 Prism Management Card User's Guide Chapter 5 ALERT Library Management Library Configuration Figure 20 Library Configuration MC350 Prism Management Card User's Guide 61 Chapter 5 ALERT Library Management Library Configuration The static settings in the Configuration section are: · · · · · · Inquiry-- model number of the library Model -- part number for the library Library Serial Number -- serial number for the library Firmware Version -- current firmware version for the library IEEE ID -- unique serial number (contained in the status code) Number Bins -- number of bins (all frames) in the library Note: The actual number of bins may vary depending on the PTM configuration. · · · · · · · · · · Library SCSI ID -- current library SCSI ID used by the external bus for a connection Number Drives -- current number of drives (all frames) in the library Barcode Retries -- current number of attempts for the library to read a cartridge bar code Online Power-Up--if selected, online power-up is activated No Barcodes--if selected, the barcode reader is deactivated Auto Load--if selected, cartridges are automatically loaded Auto Drive Unload--if selected, Auto Inventory--if selected, inventory is checked automatically on Temperature Detection--if selected, temperature detection is switched SCSI Version--this drop down box determines the SCSI version number the library will use in an Inquiry response over the SCSI interface. This option applies to the default library only, when partitioning is not enabled. If partitioning is enabled, this option will not be displayed. [. . . ] Messages that are sent to different parts of a network through SNMP. physical view A graphical representation of the library that shows the tape drives, storage bins, and load ports together with their partition owners. PMC Prism Management Card Prism Management Console Web-based interface that allows authorized staff to configure and manage all Prism storage options from behind a firewall or remotely from anywhere on the Internet. R reboot The process of restarting a computer so the operating system is reloaded. Reset button Returns the values in a dialog box to the default, or previously saved, values. [. . . ]