User manual QUANTUM 7000DLT

[. . . ] The 4000/7000DLT Tabletop Series Installation and Operation Guide © Copyright 1999 all rights reserved. Quantum® is a registered trademark and DLTTM is a trademark of Quantum Corporation. All other trademarks are property of their respective owners. Document number: 62-0162-01 Rev A First published: March 1999 Printed in the USA ii Contents 1 Introduction Overview . 2-3 Front Panel Controls and Indicators . [. . . ] Do not operate the Cartridge Insert/Release Handle. Close door and let drive complete initialization. An error has occurred. Operate Handle Green All Right Indicator Panel LEDs or, All Left Indicator Panel LEDs - ON Blinking 5-6 Operation and Maintenance 62-0162-01 Table 5-3 Operating Condition Indications Left Indicator Panel LED Label 2. 6 Color Yellow State ON Blinking Operating Condition Tape is recorded in 2. 6 format. You selected this density for a write from BOT. You selected this density for a write from BOT. You selected this density for a write from BOT. You selected this density for a write from BOT. (Compression can be done only in 10. 0, 15. 0, 20. 0, and 70. 0 density. ) Compression mode disabled. You selected a density from the front panel. Density will be selected by the host (automatic). A POST error has occurred. 6. 0 Yellow ON Blinking 10. 0 Yellow ON (default) Blinking 20. 0 (4000/7000DLT) Yellow ON (default) Blinking Compress Yellow ON OFF Density Override Yellow ON OFF (default) Blinking All Right Indicator Panel LEDs, or, all Left Indicator Panel LEDs - Blinking Drive Operating Conditions 5-7 LCD Messages Table 5-4 on page 5-8 describes the messages displayed by the LCD during normal operation: Table 5-4 Drive Operation LCD Messages LCD Message Drive Operating Condition No tape in drive. or, `4000DLT' (DLT4000) When loading or unloading a tape. DLTtype = DLT4000 (4000DLT), or DLT7000 (7000DLT). During the loading process the display may toggle between "Loading >>>" and "Calibrating>>>". Note While loading the tape, the drive will enter a false Ready Mode condition for a short period. During this false state the Tape In Use LED will continue to blink. Do not attempt any operations while the LED is blinking. When tape is unloaded. 5-8 Operation and Maintenance 62-0162-01 Table 5-4 Drive Operation LCD Messages When tape is loaded. DLTtype = DLTTM4000 (4000DLT), or DLTTM7000 (7000DLT). Compressed if compression mode enabled or Standard if compression mode disabled. 20/40GB = DLTTM4000, 35/70GB = DLTTM7000. This is the normal "Ready Screen". If write-protected tape is inserted During loading of a write-protected tape, the display will change from: "Loading>>>" to "Write Protected Tape Inside Drive", the LCD backlight will toggle on/off and an audible alarm will sound. Write-protected tape fully loaded. WPT = Write Protected Tape in unit. WPT will toggle to GB and back to WPT and continue toggling until next drive action. Drive Operating Conditions 5-9 Table 5-4 Drive Operation LCD Messages Whenever the system is writing to a tape, these two messages will alternate. Each message will be displayed for approximately 2. 5 seconds. DLTtype = DLTTM4000 (4000DLT), or DLTTM7000 (7000DLT). Compressed if compression mode enabled, standard if compression mode disabled. Writing ­ indicates the system is writing to the tape. [. . . ] Dojde-li k ruöenÌ telekomunikaËnÌch nebo jinych za¯ÌzenÌ, je uûivatel povinen provÈst takov· opat¯enÌ, aby ruöenÌ odstranil. CE Notice Marking by the symbol indicates compliance of this tape library to the EMC (Electro-magnetic Compatibility) directive of the European Community. Such marking is indicative that this tape library meets or exceeds the following technical standards: EN 55022 "Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment. " This system is an EN 55022 Class B device. EN 50082-1:1997 "Electromagnetic compatibilityGenericimmunity standard Part 1: Residential, commercial, and light industry. " EN 61000-4-2 "Electromagnetic compatibility for industrial-process measurement and control equipment Part 2: Electrostatic discharge requirements. " - Severity level 3. "Electromagnetic compatibility for industrial-process measurement and control equipment Part 3: Radiated electromagnetic field requirements. " Severity level 2. IEC 801-3 EN 55022 Compliance (Czech Republic Only) C-5 EN 61000-4-4 "Electromagnetic compatibility for industrial-process measurement and control equipment Part 4: Electrical fast transient/burst requirements. " - Severity level 2. EN60950:1992 + Amd. 1:1993 + Amd. 2:1993 with considerations to Amd. 3:1995 "Safety of Information Technology Equipment including Electrical Business Equipment. " A "Declaration of Conformity" in accordance with the preceding standards has been made and is on file at ADIC Europe, Z. A. du Bel-Air, 21 avenue Saint-Fiacre, F78100 Saint-Germain en Laye, FRANCE. VCCI Notices (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interfer-ence for information technology equipment. [. . . ]