User manual QUANTUM 7100PAK

[. . . ] 1 August 2001 Introduction 0 This document explains how to unpack the crate containing the Quantum|ATL 7100 Series library, an automated storage and retrieval system (see figure 1). After completing the instructions in this booklet, perform the set up procedure using the instructions in the Quantum|ATL 7100 Series Library Facilities Planning and Installation Guide. Figure 1 Quantum|ATL 7100 Series Library Optional Cable Cover0 The Quantum|Quantum|ATL 7100 Series library may include an optional cable cover. The cable cover ships in a separate box strapped on top of the Quantum|ATL 7100 Series crate. For information on this optional item, refer to the Quantum|ATL 7100 Series Cable Cover Installation Instructions in the cable cover shipping box. Introduction 3 Quantum|ATL 7100 Series Library Unpacking Instructions Document 6241100-03, Ver. [. . . ] Do not place static-sensitive parts on a metal surface. Place them inside their protective shipping bag or on a grounded antistatic mat. Avoid touching connectors and other static-sensitive components. Keep library doors and access panels closed whenever possible. Note: · · Dry climates and cold-weather heating environments have lower relative humidity and are more likely to produce static electricity. 6 Preparing for the Installation Quantum|ATL 7100 Series Library Unpacking Instructions Document 6241100-03, Ver. 1 August 2001 Unpacking the Library This section explains how to unpack the library and move it to its installation location. The following are the major steps in this section: · · · · Receiving the library Unboxing the library Checking the packing list Positioning the library Note: 0 Before following the instructions in this section, verify the installation site meets the requirements found in "Selecting an Installation Location" on page 4 of this document. Receiving the Library0 Inspect the shipping pallet and carton for damage that may have occurred during shipment. Report any damage to the shipper. Warning: The library weighs approximately 500 pounds (227 kg). Use at least two people to unpack, move, and install the library. Unpack the Library 0 To unpack the library: 1 Verify the minimum floor space requirements (see figure 4). Note: Unpacking the crate requires a minimum of 8 feet (2. 44 meters) in front of the library, and adequate space at the sides and back for two people to maneuver. Unpacking the Library 7 Quantum|ATL 7100 Series Library Unpacking Instructions Document 6241100-03, Ver. 1 August 2001 Figure 4 Minimum Floor Space Requirements-- Unpacking Site Library Pallet Ramp extension Unloading area (minimum) 40 in (1. 02 m) 10 ft (3. 05 m) 24 in (61 cm) 37 in (94 cm) 2 Cut the two steel bands that secure the library and packing material to the pallet (see figure 5). Caution: The steel bands are under tension and will snap away when cut. Figure 5 Removing the Steel Bands Optional cable cover Without optional cable cover RA MP SID E Steel bands RA MP SID E With optional cable cover 8 Unpacking the Library Quantum|ATL 7100 Series Library Unpacking Instructions Document 6241100-03, Ver. 1 August 2001 3 If the optional cable cover is included: · · · Remove the cable cover box from the top of the library. Refer to the Quantum|ATL 7100 Series Cable Cover Installation Instructions to install the cable cover. 4 Cut the two steel bands that secure the cardboard box to the pallet. 5 Lift the box top straight up and off the cardboard box (see figure 6). 6 Open the four retaining clips on the rear of the cardboard box. 7 Unwrap and remove the cardboard box from the library. Figure 6 Removing the Cardboard Box Box top Retaining clip Cardboard box Pallet 8 Lift the accessories tray up and off the library (see figure 7). 9 Lift the foam cap up and off the library (see figure 7). 10 Remove the two screws that secure the stop block. The stop block is located under the library in front of the casters. Unpacking the Library 9 Quantum|ATL 7100 Series Library Unpacking Instructions Document 6241100-03, Ver. 1 August 2001 11 Remove the stop block. Figure 7 Removing the Accessories Tray and Stop Block Accessories tray Foam cap Stop block 12 Pull the two ramp extensions out from under the library (see figure 8). 13 Secure the ramp extensions to the pallet using the Velcro straps. [. . . ] Close the drive access door. 3 Remove the packing material from the front door by using the procedure in step 2. 4 Remove the packing material from the storage array door: a b c If necessary, unlock the storage array door. Remove the foam sheet. Installation Procedures 13 Quantum|ATL 7100 Series Library Unpacking Instructions Document 6241100-03, Ver. 1 August 2001 Figure 11 Access Doors Load port door Storage array door Front door Drive access door 5 Remove the tie wraps from the robotics area (see figure 12): a b Remove the tie wrap that secures the gripper. Lower the foot on the low side by applying a 1/4 turn with the open-end wrench. [. . . ]