User manual QUANTUM 818126301A01

[. . . ] If necessary, position the carton so that it is top-side up. Using scissors, a utility knife, or other appropriate tool, carefully cut the packing tape along the length and ends of the carton. Remove the accessories box from the shipping carton. The accessories box contains the following items: · SCSI cable (VHDCI to 68 pin or VHDCI to VHDCI) · SCSI terminator (VHDCI terminator) · Documentation CD · Mounting hardware (brackets and screws) · Power cable d. [. . . ] Select the long or short SuperLoader brackets (depending on the depth of the rack) and attach them to the rear of the SuperLoader on the right and left sides. Bracket (right side) e. With the help of a second installer, insert the SuperLoader into the rack so that each SuperLoader bracket slides into the corresponding support bracket on the rear rails and the tabs at the front of the SuperLoader align flush with the clip nuts on the front rails. Caution: Do not let go of the front end of the SuperLoader until it can be secured to the rack. Back of SuperLoader Screws (10-32 x 1/4 only) SuperLoader bracket d. Using rack screws, attach a support bracket to the clip nuts on each rear rail. Tighten the screws just enough to hold the support brackets firmly against the rail while still allowing the support bracket to be slightly shifted by hand. This shifting will help facilitate the engagement of SuperLoader brackets as the SuperLoader is installed in the rack. You will fully tighten these screws later. Right rear rail Support brackets f. While the other installer holds the front end of the SuperLoader, secure the SuperLoader in the rack by doing the following: (1) Secure the front end tabs of the SuperLoader to the rack using four rack screws (two per tab). Make sure the screws are finger tight. Rack Left front rail Clip nuts Support bracket SuperLoader (front) Rack screws Right rear rail Rack screws Tab (one on each side) SuperLoader DLT and SuperLoader LTO Quick Start Guide Page 4 (2) Install four screws (two per side) to secure the support brackets to the SuperLoader brackets. SuperLoader bracket Support bracket b. After the cables and terminators are connected properly, tighten all screws. Screws SuperLoader (back) Right back rail VHDCI terminator installed in bottom connection of unit. Note: Not all terminators have LEDs. g. Make installation adjustments as needed. When the SuperLoader is level, tighten the screws securing the SuperLoader tabs to the front rails, the SuperLoader brackets to the support brackets, and the support brackets to the rear rails. Make sure the terminator is placed on the bottom connector of the unit and the host cable going to the server is located at the top, as pictured above. Note: On all SuperLoaders, SCSI terminators must be used for proper operation of the drive. Step 5: Establish the SCSI Connection a. Make sure the supplied SCSI cable matches the host computer HBA SCSI input. The host may support VHDCI or 68 pin. Note: Do not turn on the host computer or any devices connected to the host computer until you have configured the SuperLoader and installed tape cartridges. Step 6: Network Connection to the SuperLoader Network connection is IP configurable through the front panel of the SuperLoader. · DLT models auto negotiate speed of network connection 10/100. · LTO models can select the network speed from the front panel under Configuration>10/100. Connect the network cable to the RJ45 connector found on the back of the SuperLoader as illustrated on the next page. SCSI 68-pin connector VHDCI SCSI VHDCI terminator Properly turn off all peripheral devices connected to the host computer, then properly shut down the host computer. Note: When connecting SCSI cables, make sure you correctly align the connector to avoid bending connector pins. Step 7: Power Supply Cable Connection The power supply cable should be connected to the input power connection on the back of the SuperLoader as illustrated on the next page. SuperLoader DLT and SuperLoader LTO Quick Start Guide Page 5 Power connector Step 9: Verify Robot/Drive Seen by the Operating System Windows 2000: Under Device Manager, an unknown media changer should be present. Under Tape Drive, you should see the drive that is configured for your SuperLoader. Sun: During reboot, break the standard initialization and do a probe scsi all. This should show the SuperLoader and the drive configured for the unit. Step 10: Configuration of the Web Interface RJ45 connection for Web interface: Login: guest Password: guest Host cable end (can be VHDCI or 68 pin) VHDCI connection (host cable at the top, terminator at the bottom) Obtain the IP address from your network administrator, or the host DHCP server will provide you the IP address. [. . . ] Note: These instructions are for both the SuperLoader DLT and SuperLoader LTO due to the nature of their similarities. Many component parts are not interchangeable. These include the magazines, cartridges, drive carrier assemblies, magazine blanks, magazine handles, and the bar code scanner. Please order the appropriate part numbers when replacing these items. Caution: When removing magazines or blanks, be certain that no robotic operations are in process. [. . . ]