User manual QUANTUM ATL M2500 UNPACKING INSTRUCTIONS 05-2003

[. . . ] Quantum ATL M2500 Unpacking Instructions Introduction Removing the Library from the Shipping Carton Removing the Remaining Packing Materials Checking the Contents 3 3 10 21 Document 6423000-04 A01, May 2003 1 Quantum ATL M2500 Unpacking Instructions Document 6423000-04 A01 May 2003 2 6207947-05fN 11 Quantum ATL M2500 Unpacking Instructions Document 6423000-04 A01 May 2003 Introduction This document explains how to unpack the ATL M2500 library. Warning: 0 This document is provided as a reference only. This product requires professional installation by Quantumauthorized personnel. [. . . ] At the top of the library, unhook the straps. 11 Remove the accessory boxes from the sides of the library and set them aside (see figure 6). Figure 6 Removing the Straps and Accessory Boxes Accessory boxes Straps 12 Remove the shipping panels from the library (see figure 7): a With the help of another person, tilt the library to the left slightly so that the right side of the library lifts up from the ground approximately 1 in. Grip the top of the right shipping panel and pull it away from the library. The bottom of the panel disconnects from the bottom of the library. b Removing the Library from the Shipping Carton 9 Quantum ATL M2500 Unpacking Instructions Document 6423000-04 A01 May 2003 c d Set the panel aside. Repeat steps 12a through 12c on the other side to remove the left shipping panel. Shipping panels Figure 7 Removing the Shipping Panels Removing the Remaining Packing Materials Now that you have removed the library from its shipping carton, remove the remaining packing materials from the library: 0 1 Remove the transit screw from the top of the library and set it aside (see figure 8). Later in this procedure you will place the transit screw in a storage location within the library in case it is needed for future repackaging and shipment of the library. Caution: The transit screw secures the library robotics. Do not try to move the library robotics unless this screw and the two transit screws securing the X-Y tray (removed later during this procedure) have been removed; moving the robotics with the transit screws in place can cause serious damage to the library. 10 Removing the Remaining Packing Materials Quantum ATL M2500 Unpacking Instructions Document 6423000-04 A01 May 2003 Figure 8 Removing the Transit Screw Transit screw 2 Put on an antistatic wrist strap and clip it to the antistatic stud on the back of the library. the doors. 3 Press the buttons next to the three magazine access doors and open 4 Remove the four pieces of packing foam from the front of the magazines (see figure 9). Figure 9 Removing the Magazine Packing Foam Packing foam Note: Library levels are numbered from top to bottom. The top magazines in the library are at level 1; the bottom magazines are at level 4. Removing the Remaining Packing Materials 11 Quantum ATL M2500 Unpacking Instructions Document 6423000-04 A01 May 2003 Figure 10 Magazine Access Door Buttons Left magazine access doors Left magazines Magazine access door buttons Right magazines Right magazine access door Level 1 Level 2 Level 3 Level 4 5 Remove the level 1 left magazine: a b c Grasping the handle at the front of the level 1 left magazine, pull it forward until it stops. If the magazine stops after the first slot, perform steps 5c through 5e to release it. Remove the level 2 left magazine (see figure 11). Figure 11 Removing the Level 2 Left Magazine 12 Removing the Remaining Packing Materials Quantum ATL M2500 Unpacking Instructions Document 6423000-04 A01 May 2003 d Reach into the library underneath the level 1 left magazine and pull down on the release latch (see figure 12). Figure 12 Release Latch Release latch e While holding the release latch, pull the level 1 left magazine forward and out of the library (see figure 13). Figure 13 Removing the Level 1 Left Magazine Removing the Remaining Packing Materials 13 Quantum ATL M2500 Unpacking Instructions Document 6423000-04 A01 May 2003 6 Remove all remaining magazines by grasping the handle at the front of each magazine and sliding it forward and out of the library. Caution: When reaching into the library through the magazine access doors, be careful not to exert pressure on the magazine shelves. Excessive pressure may bend the shelves. 7 Remove the pad from the X-Y platform lift cable (see figure 14): a With your right hand, reach into the library through the empty level 2 right magazine slot and gently pull the X-Y platform lift cable towards you. With your left hand, reach into the library through the empty level 2 left magazine slot, remove the foam pad from the cable, and pull it out of the library. Release the X-Y platform lift cable. b c Figure 14 Removing the Foam Pad from the X-Y Platform Lift Cable (Magazines and drives omitted for clarity) X-Y platform lift cable 14 Removing the Remaining Packing Materials Quantum ATL M2500 Unpacking Instructions Document 6423000-04 A01 May 2003 8 Remove the robotic hand pad assembly: a Reach through the open right magazine access door and to the left. [. . . ] Refer to the Quantum ATL M-Series Library Installation Guide (6423001) for installation instructions. Checking the Contents 0 Compare the contents of the shipping carton and the accessories kit with the items listed on the label on the outside of the shipping carton. If any items are missing or damaged, contact your authorized reseller. Note: The tape drives are sent separately from the library. Checking the Contents 21 Quantum ATL M2500 Unpacking Instructions Document 6423000-04 A01 May 2003 22 Checking the Contents [. . . ]