User manual QUANTUM ATL POWERSTOR L500 V3 REL 0

[. . . ] Quantum|ATL PowerStor L500 Series Tape Library User's Guide 6321100-03 Ver. 3, Rel. 0 Quantum|ATL PowerStor L500 Series Library User's Guide, 6321100-03, Ver. Quantum|ATL provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum|ATL may revise this publication from time to time without notice. [. . . ] option gives status information only and there are no commands to be issued; therefore the ENTER button is not functional. options and their respective messages. Quantum|ATL PowerStor L500 Series Tape Library User's Guide 39 Chapter 3 Basic Library Operations Status Table 5 Status Options Option Slot Status Description Displays status of all magazine slots. Message Cartridge Status: 0 67 13 Note where: = cartridge present 0 1 2 = cartridge in drive 0, 1, or 2 = empty slot (dash) = missing m = in transit (cartridge in t CHM) Drv 0-Drv 2 Displays tape drive status including tape drive error conditions and cartridge conditions. Status: COMP - If the last read or write operation was data compressed, COMP is displayed in addition to the status message. a · Empty · InFlux (drive is becoming ready) · Cln (cleaning required) · Code Update (updating firmware) · Calibrating · Unloading · Loading · Cleaning · Erasing · Writing · Reading · Seeking · Rewinding · Idle 40 Quantum|ATL PowerStor L500 Series Tape Library User's Guide Chapter 3 Basic Library Operations Status Option Drv 0-Drv 2 Description Displays tape drive status including tape drive error conditions and cartridge conditions. Message Error: Note CLN - If the tape drive head requires cleaning, CLN is displayed in addition to the status message. · Hardware Error · Comm Error · Library Error Slot 0123. . . 13 Bar code: ___* Displays specific slot status. in Drive # Empty Full In transit Missing If applicable, the second line of this message displays a bar code label entry. a. a. When using an unrecorded tape, the tape drive defaults to native tape density if a write from the beginning of tape (BOT) is executed. If you execute a write from the beginning of tape (BOT) when using an unrecorded tape, the tape drive defaults to native tape density. If you execute a write from the BOT when using a recorded tape, all pre-recorded data (and density changes) are lost. This includes density changes because they are established when writing from the BOT. Quantum|ATL PowerStor L500 Series Tape Library User's Guide 41 Chapter 3 Basic Library Operations Eject/Unlock Eject/Unlock 3 The EJECT/UNLOCK?option unlocks the library door and ejects a cartridge from the tape drive. Caution: Do not press PREVIOUS, NEXT, SELECT or ENTER until the backup or other tape operations are stopped at the host; pressing these buttons while other operations are executing may result in operation or drive failure. options and their respective messages. Table 6 Eject/Unlock Options Option Description Unloads the cartridge from the tape drive and reports on drive status Ejects any cartridge that is in a drive then unlocks the library doors Message Notes The Eject function unloads the cartridge from the tape drive. The library door is unlocked. Eject Cartridge?Doors Unlocked! 42 Quantum|ATL PowerStor L500 Series Tape Library User's Guide Chapter 3 Basic Library Operations Eject/Unlock Opening the Library Doors 3 Caution: Never force the library door open. message is displayed to verify that the library locking mechanism has completed the unlocking activity. To open the library doors: 1 2 3 4 5 Press SELECT. Press ENTER to answer Yes. The loader removes all cartridges from each drive and displays Open Doors!This activity can take up to three minutes if a rewind from end of tape is required. The library doors are now unlocked. Closing the Library Doors 3 To close the library doors, push each door closed until it latches. The door will lock automatically after approximately five seconds. The library executes a scan magazine function. If the optional bar code reader is present, the cartridge labels are read. Unloading a Cartridge from the Tape Drive 3 To unload a cartridge from the tape drive: 1 2 Press SELECT until EJECT/UNLOCK?is displayed. Quantum|ATL PowerStor L500 Series Tape Library User's Guide 43 Chapter 3 Basic Library Operations Eject/Unlock 3 Press ENTER. One of the following messages is displayed: · · · Drive is Empty Drive NOT Present Eject to Slot 0? 4 If Drive is Empty or Drive NOT Present is displayed, there is no cartridge to unload in drive 0. 5 Press NEXT. [. . . ] En cas d'envoi aux États-Unis, utiliser le cordon d'alimentation CERTIFIÉ UL et convenant pour 100-120 V. En cas d'envoi au Canada, utiliser le cordon d'alimentation CERTIFIÉ CSA et convenant pour 100-120 V. Fiche Broches parallèles avec une broche de mise à la terre (configuration NEMA 5-15P) Type: SJT, trifilaire 16 AWG (1. 5 mm2) ou 18 AWG (1. 0 mm2) Cordon LongeurMaximum 15 pieds (4. 5m) CapacitéMinimum 10 A, 125 V Quantum|ATL PowerStor L500 Series Tape Library User's Guide 97 INDUSTRY CANADA (DIGITAL APPARATUS) Interference-Causing Equipment Standard ICES-003 Issue 2 98 Quantum|ATL PowerStor L500 Series Tape Library User's Guide Glossary A Access time The interval between the time a request for data is made by the system and the time the data is available from the drive. Actuators Robotic components inside the library that move cartridges. Archiving The tape library provides long-term storage of important information on magnetic tape. DLTtape media has a 30year shelf-life. AutoClean A user-defined mode in which the library automatically performs drive cleaning tasks as needed. Autoload A user-defined mode in which the library automatically moves cartridges in the load port to empty storage bins as soon as the load port door is closed. C CHM The Cartridge Handling Mechanism, also referred to as the elevator, or robot, is the means for transporting tape cartridges. [. . . ]