User manual QUANTUM DAT 320 QUICK GUIDE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual QUANTUM DAT 320. We hope that this QUANTUM DAT 320 user guide will be useful to you.

Lastmanuals help download the user guide QUANTUM DAT 320.


Mode d'emploi QUANTUM DAT 320
Download

You may also download the following manuals related to this product:

   QUANTUM DAT 320 REV B (1146 ko)

Manual abstract: user guide QUANTUM DAT 320QUICK GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] · Hold the drive by its edges only. Avoid touching any exposed parts on the printed circuit board. · Always place the drive on top of or inside the antistatic bag to reduce the chance of ESD damage Preinstallation Requirements In addition to the contents included with your internal tape drive, you need the following items to install your internal tape drive. · A USB 2. 0 port · 5. 25-inch half-height bay (for internal drive) · Backup application software that supports the internal tape drive. [. . . ] If in doubt, refer to your server documentation. Mounting Screws Other server models only require the use of special locating screws with no mounting rail. 1 Use a screwdriver to attach the appropriate screws. You may need to purchase the M3 screws separately. Position the screws (see Figure 1). Figure 1 Attaching Mounting Screws 4 Installing the Internal DAT 320 Tape Drive in Your Server DAT 320 2 Attach the appropriate mounting hardware. Refer to the manufacturer's documentation for instructions. · If you are installing on a server that requires a tray, place the tape drive in the tray. · If you are installing in a server that requires mounting rails, fasten the rails to the tape drive. · Some servers have snap-on mounting rails attached to the filler panel. These can be removed and attached to the tape drive with screws. Installing the Tape Drive To install the tape drive: 1 Slide the tape drive into the open bay aligning the tray or rails with the slots in the bay (see Figure 2). Figure 2 Installing the Tape Drive If your server does not use mounting hardware, check that the holes in the chassis are aligned with the holes in the side of the tape drive. Do not secure the drive at this point because you may have to move the drive to get the cables into place. Installing the Internal DAT 320 Tape Drive in Your Server 5 DAT 320 Quick Start Guide Attaching the USB Cable Decide Which Cable to Use There are several options for connecting the tape drive to your server: To an . Internal standard USB port External USB port Use . standard USB cable standard USB cable Notes May be connected to the server's system board or an internal USB card. Cable routing kit is required. Connecting the USB Cable from the Tape Drive to the Server To an Internal USB 2. 0 Port 1 Use the schematic on the inside of the server panel to check whether your server has an internal USB 2. 0 port and locate its position. 2 Use the appropriate cable to connect to the server. · A standard 5-pin USB Type B cable is provided with the tape drive (see Figure 3). Figure 3 Connecting to an Internal USB Port 6 Installing the Internal DAT 320 Tape Drive in Your Server DAT 320 To an External USB 2. 0 Port Purchase a special USB cable and Cable Routing Kit. The Cable Routing Kit consists of a bracket with attached cable on one side that connects to the server's external port and a Type A USB socket on the other side. Make sure you orientate the bracket correctly when you fit it (see Figure 4). 1 Remove a spare blanking plate from the rear panel of the server. 2 Fit the bracket with attached the cable and fix it to the server. Make sure the cable is outside of the server and connect it to the server's external USB port (see Figure 4). 3 Attach the standard USB cable to the bracket (type A connector) (see Figure 4). Figure 4 Connecting the USB Cable Type B connector to tape drive Type A connector on inside of bracket Type A connector to server's external USB port Attaching the Power and USB Cables to the Tape Drive Note: The drive is not powered from the USB bus. It must be connected to the server's power supply. [. . . ] or the Canadian Standards Association in North America). You should also consider the following safety points: · Install the drive in an enclosure that limits the user's access to live parts, gives adequate system stability, and provides the necessary grounding for the drive. · Provide the correct voltages (+5 VDC and +12 VDC) based on the regulation applied--Extra Low Voltage (SEC) for UL and CSA, and Safety Extra Low Voltage for BSI and VDE (if applicable). Electromagnetic Compatibility (EMC) Compliances 13 DAT 320 Quick Start Guide *6-66928-01* 14 6-66928-01 Rev B September 2010 For assistance, contact the Quantum Customer Support Center: USA: 800-284-5101 (toll free) or 949-725-2100 EMEA: 00800-4-782-6886 (toll free) or +49 6131 3241 1164 APAC: +800 7826 8887 (toll free) or +603 7953 3010 Worldwide: http://www. quantum. com/ServiceandSupport About Quantum Preserving the World's Most Important Data. Yours. TM ©2010 Quantum Corporation. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE QUANTUM DAT 320

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual QUANTUM DAT 320 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag