User manual QUANTUM DX-SERIES 08-2005

[. . . ] Quantum DX-Series User's Guide, 6513501-04 A01, August 2005, Made in USA. Quantum Corporation provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice. COPYRIGHT STATEMENT Copyright 2005 by Quantum Corporation. [. . . ] Only tape drive 2 and 3 are visible from port 6. 6 When all of the virtual devices have been assigned to the appropriate port, click Apply to accept the port settings. Note: Microsoft Windows has a known issue recognizing more than eight LUNs on a single Fibre Channel port. See Microsoft Knowledge Base Article 310072: http://support. microsoft. com/default. aspx?scid=kb;en-us;310072 for information on reconfiguring Windows to overcome this limitation. System Status 3 The System Status page allows you to view information on the emulated tape drives, robot, storage bins, and DX-Series system hardware. Accessing System Status 3 To access the System Status page, from the contents frame, click System Status. The management frame displays the System Status page (see figure 33). 54 Quantum DX-Series User's Guide Chapter 3 DX-Series Remote Management System Status Figure 33 System Status Page The system status page provides two views for the system hardware: · Physical View The physical view displays the physical representation of the virtual components (tape drives, tape cartridges, and robots) of the emulated tape library. Each drive and tape cartridge is displayed in the tape drive and storage bin sections. Clicking on a tape drive or cartridge displays the specific details for that device on the right hand side of the page. Select the partition you wish to view from the drop down list. The Show/Hide links will either display or hide information on the selected tape drive, tape cartridge, or robot. Clicking on a tape drive, tape cartridge, or robot displays detailed information about the selected device. · Logical View A logical view displays the partitions within the DX-Series system. Clicking on a partition displays the specific details for that partition on the right hand side of the page. · Events The events list displays all events that have occurred on the DXSeries system. Quantum DX-Series User's Guide 55 Chapter 3 DX-Series Remote Management System Status Viewing Tape Drive Details To view the tape drive details: 3 1 From the System Status page, select the partition from the drop down list and click the tape drive you wish to view. The tape drive details displays (see figure 34): Figure 34 Tape Drive Details Selected tape drive Tape drive details The tape drive details are shown in table 7. Table 7 Tape Drive Details Field Status Compression Description Displays the current drive status. The drive can be reading, writing, or idle. Displays the compression status, either enabled or disabled. 56 Quantum DX-Series User's Guide Chapter 3 DX-Series Remote Management System Status Field Contents Description Displays the current contents of the tape drive. If a tape cartridge is present in the drive, the cartridge label will display in the contents field as well as the write protect status and capacity information. Displays the manufacturer of the tape drive. Displays the logical unit of the tape drive. Displays the port number assigned to the tape drive. Brand Model Serial Number LUN Port Viewing Robot Details To view the robot details: 3 1 From the System Management page, click Show Robots to view the details. The robot details displays (see figure 35): Quantum DX-Series User's Guide 57 Chapter 3 DX-Series Remote Management System Status Figure 35 Robot Details Robot Robot details The robot details are shown in table 8. Table 8 Robot Details Field Status Contents Description Displays the current status of the robot. Displays the current contents of the robot. If a cartridge is present, the bar code label appears in the robot contents. Displays the robot serial number. Brand Model Serial Number 58 Quantum DX-Series User's Guide Chapter 3 DX-Series Remote Management System Status Viewing Storage Bin Details 3 To view the storage bin details: 1 From the System Management page, click the storage bin to view the details. The storage bin details displays (see figure 36): Figure 36 Storage Bin Details Storage bin Storage bin details The storage bin details are shown in table 9. Quantum DX-Series User's Guide 59 Chapter 3 DX-Series Remote Management System Status Table 9 Storage Bin Details Field Status Contents Description Displays the current status of the storage bin. [. . . ] Om batteriet byts ut mot ett nytt av fel typ föreligger risk för explosion. Begagnade batterier ska hanteras i enlighet med gällande föreskrifter. Litium kan betraktas som ett riskmaterial. Kassera batteriet i enlighet med gällande lokal och nationell lagstiftning. 126 Quantum DX-Series User's Guide Appendix C Regulatory Statements Power Cord Statement Warning Disconnect all power cords before servicing. Avertissement Déconnectez tous les fils électriques avant d'effectuer des réparations. Warnung Vor der Wartung alle Netzkabel abziehen. Attenzione Prima di effettuare qualsiasi intervento di manutenzione, scollegare tutti i cavi di alimentazione. Advertencia Desconecte todos los cables de alimentación antes de dar mantenimiento. Varning Koppla bort alla nätsladdar innan service utförs. Quantum DX-Series User's Guide 127 Appendix C Regulatory Statements Disposal of Electrical and Electronic Equipment 3 This symbol on the product or on its packaging indicates that this product should not be disposed of with your other waste. [. . . ]