User manual QUANTUM FREEXWIRE FW9T

[. . . ] OPERATING INSTRUCTIONS model FW7Q, FW8R Digital Receivers model FW9T Digital Transmitter Digital Wireless TTL Flash and Camera Trigger DESIGNED AND MANUFACTURED IN THE USA Patent Pending Contents Section . . Wireless Flash setup -- with or without on-camera Flash . . Wireless Shutter Release (motor drive) . . Changing Qflash settings via Wireless Remote . [. . . ] FW7Q, FW8R and FW9T provide wireless QTTL flash capability for these types of camera systems, whether digital or film camera systems. "Dw" series QTTL adapters (e. g. D12w, D13w, etc. ) and Qflash series 5d flashes are required for the functions of this Section 7. 0. Note: All Qflash 4d series flashes can be converted to Qflash 5d series, and all D series adapters can be converted to Dw series via software upgrades. Please contact Quantum Customer Service for the upgrade procedure. If you wish to utilize FREEXWIRE FW10 transceivers together with FW7, 8, or 9 units, they require an upgrade to FW10w for the functions Sections 7. 0 and 8. 0. Please contact Quantum Customer Service for the upgrade procedure. FW10w can not be directly connected to Dw series QTTL Adapters (sections 7. 1, 8. 1). A local Qflash is required as illustrated in sections 7. 3 and 8. 3. 7. 1 Transmitter FW9T set-up Select the Dw series QTTL Adapter compatible with your camera (Appendix D, or www. qtm. com for latest additions). Mount the Dw series adapter to the camera and connect its cable to the FW9T Accessory socket. Mount FW9T on a bracket or other convenient location. 7. 2 Receiver FW8R or FW7Q set-up Important: Set receivers FW7Q or FW8R to NORM range only for wireless TTL. Connect FW31 Accessory Cable between the Receiver FW8R and either Qflash 5 series Accessory socket. Qflash powers FREEXWIRE, and batteries are not needed, when it is connected with the QF31 cable. FW7Q plugs directly into a Qflash 5d series as described in Section 5. 4. QFLASH 5D FW8R FW31 MOUNTING FW7Q 7. 3 Connecting a local Qflash to the Transmitter FW9T If you wish to sync an on-camera Qflash 5 series with all remote Qflashes, connect the "Dw" series TTL Adapter to either Qflash Accessory socket. Connect the FW9T to the other Accessory socket with an FW31 accessory cable. Qflash cannot be deactivated with the Local switch on FW9T. However, Qflash 5 series can be turned off by pressing MODE twice. FW9T FW9T Dw SERIES QTTL ADAPTER Dw SERIES ADAPTER FW31 Important: On left side of FW9T case set TTL switch to ON. FW31 12 13 8. 0 Wireless TTL control for Film Cameras 4. 0 (non pre-flash) This mode allows a (non pre-flash) TTL camera to control all local and remote Qflash exposures. All series of Qflash and all series of TTL adapters can be used, including QFT, X, T2, X2, T2d, X2d, 4 and 5 series, and TTL adapter series QF, FW, D, and Dw. Set all Qflashes, on-camera or remote, to TTL mode. [. . . ] 25 fps ** QF series TTL Adapters require an FW11 Uni-Mod connected to FREEXWIRE TX, unless a Qflash is also connected to the Accessory connector of FREEXWIRE. *** D series QTTL Adapters provide the most features, including auto-focus, fill flash offset, etc. Adapters models may be changed or updated periodically. Please check the latest Quantum Price List at your dealer, or www. qtm. com. [. . . ]