User manual QUANTUM P7000 UNPACKING INSTRUCTIONS V2 REL 0

[. . . ] The floor must be level to within 0. 25 inch (6. 4 mm) over a 6-foot-by-6foot (1. 83-meter-by-1. 83-meter) area. Power and Grounding 0 For the United States and Canada, one or two UL/CSA certified power cords are furnished. Each uses a 14/3 SJT cord, a 5-20P plug, and an IEC-C320 C19 female connector (see figure 3). Connects to wall outlet Connect to library power supply Figure 3 Power Supply Cord Plug: NEMA 5-20 Connector: IEC-C320 C19 The library is rated 100-240V~, 50-60Hz, 16A-8A, 1600W. The library power requirements may require modification of the facilities existing power capabilities by a qualified electrician. The required wall outlet for the United States and Canada is rated at 125V 20A (see figure 4). Figure 4 Wall Outlet Neutral Ground Line Wall outlet: NEMA 5-20R rated 125V 20A The dedicated wall outlet and a 20 amp circuit breaker must provide power to the ATL P7000 only. [. . . ] Report any damage to the shipper. Caution: The ATL P7000 with 16 DLT7000 tape drives weighs approximately 1444 pounds (656 kg). Use at least two people to move and install the library. Unpacking the Library 7 Quantum ATL P7000 Unpacking Instructions Document 6434006-02, Ver. 0 August 2002 Unboxing the Library 0 To unbox the library: 1 Choose the unloading side. The ATL P7000 may be unloaded from either the right or left side of the pallet. 2 Verify the minimum floor space requirements (see figure 5). Note: Uncrating the library requires a minimum of 3 feet (91 cm) on all sides. For the side being used for the ramp, uncrating the library requires an additional 7 feet (2. 13 m) for a total of 10 feet (3. 05 m) on that side. Figure 5 shows the minimum floor space required by the ATL P7000 at its uncrating site. The minimum height required for unpacking the ATL P7000 is 85 inches (2. 16 meters). Figure 5 Minimum Floor Space Requirements-- Uncrating Site 3 ft (92cm) Accessory kits Rear Library Ramp extensions 3 ft (92cm) 10 ft (3. 05 m) for ramp extensions 3 ft (92cm) 10 ft (3. 05 m) for ramp extensions 3 ft (92cm) Front 3 Cut the two steel bands that secure the library and packing material to the pallet (see figure 6). Caution: The steel bands are under tension and will snap away when cut. 8 Unpacking the Library Quantum ATL P7000 Unpacking Instructions Document 6434006-02, Ver. 0 August 2002 Figure 6 Removing the Steel Bands 4 Lift the cardboard box top cover straight up and off of the pallet (see figure 7). Figure 7 Removing the Box Top Cover 5 Pull the eight cardboard box retaining clips to their open position. 6 Unwrap the cardboard box from the library (see figure 8). Unpacking the Library 9 Quantum ATL P7000 Unpacking Instructions Document 6434006-02, Ver. 0 August 2002 Figure 8 Removing the Cardboard Box 7 Remove the accessory kits from the rear compartment of the crate. 8 Check the packing list and verify that all accessories have been received. Note: If any part is missing or damaged, contact your authorized reseller. 9 Lift the foam cap up and off of the library (see figure 9). 10 Unpacking the Library Quantum ATL P7000 Unpacking Instructions Document 6434006-02, Ver. 0 August 2002 Figure 9 Removing the Foam Cap 10 On the right side of the library, lift the wooden bar out of its brackets on the pallet (see figure 10). Figure 10 Removing the Wooden Bar 11 On the right side of the library, unscrew the bolts that secure the hold-down brackets. Each hold-down bracket is secured with two bolts. figure 11). 12 Remove each hold-down bracket from under the library (see Unpacking the Library 11 Quantum ATL P7000 Unpacking Instructions Document 6434006-02, Ver. 0 August 2002 Figure 11 Removing the Stop Blocks 13 Reinsert the left-side wooden bar in its brackets on the pallet to hold the library in place. 14 Repeat steps 10, 11, and 12 for the left side of the library. 15 Slide out the two ramp extensions and the foam block, all located under the library on the right side (see figure 12). Figure 12 Removing the Ramp Extensions 16 Place the ramp extensions aside until the library is ready to be positioned. 12 Unpacking the Library Quantum ATL P7000 Unpacking Instructions Document 6434006-02, Ver. 0 August 2002 17 Re-insert the right-side wooden bar into its brackets on the pallet to hold the library in place. Positioning the Library 0 To position the library: 1 Map out a route to the installation site. 2 Carefully lift the shipping bag off of the library (see figure 13). Figure 13 Removing the Shipping Bag 3 Inspect the library for any damage that may have occurred during shipment. 4 Place the two ramp extensions in the slots provided at the edge of the pallet (see figure 14). The ramp may be set up on either the right side or the left side of the pallet. Note: The following illustrations show the ramp set-up procedure from the right side of the library. Unpacking the Library 13 Quantum ATL P7000 Unpacking Instructions Document 6434006-02, Ver. 0 August 2002 Figure 14 Preparing the Ramp 5 Verify that the library's four leveling feet are raised. If not, raise each foot as needed as by turning the leveling foot until it is 1/2 inch above the pallet (see figure 15). Figure 15 Raising the Leveling Feet 14 Unpacking the Library Quantum ATL P7000 Unpacking Instructions Document 6434006-02, Ver. [. . . ] 6 Place the shipping bag, load port shipping plate, stop blocks, foam cap, screws, and other packaging materials on the pallet. 7 Collapse the cardboard box. 8 Place the cardboard box on top of the packaging materials on the pallet. 9 Secure the pallet, packaging materials, and cardboard box for future use. Leveling the Library 0 To level the library: 1 Rotate each foot of the library until it makes contact with the floor. 2 Rotate each foot an additional 1/4 turn with the open-end wrench to begin raising the library. 3 Center a carpenter's level on the top front edge of the library. Unpacking the Library 21 Quantum ATL P7000 Unpacking Instructions Document 6434006-02, Ver. 0 August 2002 4 Check the gauge on the level. [. . . ]