User manual QUANTUM PX500 TAPE DRIVE INSTALLATION INSTRUCTIONS 81-81301-01 B01

[. . . ] Quantum PX500 Series Library Tape Drive Installation Instructions Introduction 3 Tape Drive Numbering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Upgrade Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Unpacking the Tape Drive Installing the Tape Drives Cabling the Tape Drives Setting the Tape Drive SCSI ID 7 7 8 11 Setting the SCSI ID Using the OCP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Setting the SCSI ID from the Remote Management Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 81-81301-01 B01, May 2005 1 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 2 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 Introduction 0 This document provides instructions for adding a tape drive to an Quantum PX500 Series tape library. The tape drive upgrade procedure consists of the following steps: · · · · Unpacking the Tape Drive Installing the Tape Drives Cabling the Tape Drives Setting the Tape Drive SCSI ID Tape Drive Numbering 0 The Quantum PX500 Series tape library may contain up to 10 tape drives depending on the library model. Refer to the following figures: · · · Figure 1 - PX502 Tape Drive Numbering (up to two tape drives) Figure 2 - PX506 Tape Drive Numbering (up to six tape drives) Figure 3 - PX510 Tape Drive Numbering (up to ten tape drives) Figure 1 Quantum PX502 Tape Drive Numbering Tape drive 2 Tape drive 1 Introduction 3 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 Figure 2 Quantum PX506 Tape Drive Numbering Tape 2 drive 1 Tape drive 1 Tape 4 drive 2 Tape drive 3 Tape 6 drive 5 Tape drive 5 4 Introduction Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 Figure 3 Quantum PX510 Tape Drive Numbering Tape drive 2 Tape drive 1 Tape drive 4 Tape drive 3 Tape drive 6 Tape drive 5 Tape drive 8 Tape drive 7 Tape drive 10 Tape drive 9 Introduction 5 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 Upgrade Kits 0 The tape drive upgrade kit differs depending on the tape drive type needed for the library (refer to table 1): Table 1 Tape Drive Upgrade Kits Part Number PR-UU1QA-YF (SDLT -600) PR-UU2QA-YF (HP-LTO2) PR-UU3QA-YF (HP -LTO3) SDLT -600 Tape Drive Module HP-LTO2/3 Tape Drive Module Required Tools 0 The following tools are required to perform the tape drive upgrade procedure: · Flat blade screwdriver Use appropriate electrostatic discharge (ESD) precautions when installing the tape drive. Caution: 6 Introduction Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 Unpacking the Tape Drive To unpack the tape drive: 1 Open the shipping carton. [. . . ] Note: The library assigns SCSI IDs based on the drive order. Drive bay 1 = SCSI ID 1, drive bay 2 = SCSI ID 2, and so forth. It is only necessary to perform the steps in this section if you need to set the tape drive SCSI ID to an ID other than the default. 0 There are two ways to set the tape drive SCSI ID: · · Setting the SCSI ID Using the OCP Setting the SCSI ID from the Remote Management Pages Setting the SCSI ID Using the OCP To set the tape drive SCSI ID on an PX500 Series library with an LCD: 0 1 From the operator control panel (OCP), press Setup from the Home screen. The OCP displays the Setup screen (see figure 8): Figure 8 Setup Screen Enter 2 Use the up and down arrows to highlight Cabinet and press Enter. The Cabinet screen displays (see figure 9): Figure 9 Library Options Screen 3 Use the up and down arrows to highlight Host bus and press Enter. The Host bus screen displays (see figure 10): Setting the Tape Drive SCSI ID 11 Quantum PX500 Series Tape Drive Installation Instructions 81-81301-01 B01 May 2005 Figure 10 Host Bus Options Screen 4 Use the up and down arrows to highlight the tape drive receiving the new SCSI ID and press Enter. 5 Use the up and down arrows to select a SCSI ID and press Enter to set the ID. 6 When you have completed setting the SCSI IDs, press Exit to return to the Cabinet screen. 7 From the Ops screen, use the up and down arrows to highlight Drive Operations and press Enter. The Drive Operations screen displays (see figure 11): Figure 11 Drive Operations Screen 8 Use the up and down arrows to select a tape drive and press Enter. 9 Use the up and down arrows to select Off and press Enter. The tape drive powers down and returns to the Drive Operations screen. 10 Use the up and down arrows to select On and press Enter. The tape drive powers on and is ready for use. [. . . ] The Drives page displays (see figure 14): Figure 14 Drives Page Drive operations 8 Enter the new tape drive number 9 Select shutdown and click Apply. 10 Enter the new tape drive number 11 Select Power on and click Apply. The tape drive installation is complete. 14 Setting the Tape Drive SCSI ID [. . . ]