User manual QUANTUM SCALAR 10K 320A.00004 RELEASE NOTES 09-2007

[. . . ] Visit http://www. quantum. com for additional information about the Scalar 10K and previous releases. © September 2007 Quantum Corporation. Document 6-00016-32 Rev A Quantum, Scalar, DLT, DLTtape, the Quantum logo, and the DLTtape logo are all registered trademarks of Quantum Corporation. SDLT and Super DLTtape are trademarks of Quantum Corporation. LTO and Ultrium are trademarks of HP, IBM and Quantum in the U. S. A. [. . . ] Need to have option to speed up I/E station teach operations. DLT-8000 Sleds incorrectly log a stepper motor task fails to start. Get/put window test doesn't reserve library, interference with auto reteach. Get SAC 7C and Library TA flag 13 instead of TA flag 2 when move tape to blocked storage Resolved Issues 3 Release Notes Document 6-00016-32 Rev A September 2007 Change Request Number 2876 2911 2931 2938 Service Request Number Description Logical serial number (12 character) causing configuration errors with TSM application. IVT test does not run LTO move cartridge test in 4th IE. 418156 Library should compare drive fiducial labels with actual sled type. Service login timeout is handled incorrectly at "service->verify->all>perform all tests" screen if the 'Accept' input is 'y' when the timeout occurs. Remove fibre channel topology and data rate selection for LTO-1 FC drives. S10K Tape alert flags are reported incorrectly in the S10K log and need a mechanism to report tape alert log data back to SDLC. 2939 2974 3024 3031 3032 3038 3041 3045 3050 3071 3073 3074 3075 3081 3352 582456 566896 527016 622572 550364 If the IE cable between the IE and the LMC becomes disconnected and a new teach is performed the teach fails with SAC 01, 40, A3. On large dual aisle systems, it has been observed that tower 13 sometimes fails to teach new on the secondary aisle side. Serial number and logical serial number are truncated by 1 character on the operator panel. E_LSC_WFSCRDBF_BAD_READBUFFER_HANDLE is reported with RMU 192 and 304 Library firmware. If a LTO barcode label is printed in the reverse direction the library incorrectly places the label into the bottom cell and forces a rescan. Need to merge changes form CR64557(support of LB and LX media for 3592 drives) onto main tree for 320. On systems with a lot of drives (70+ drives), the Log sense page 3B interferes with vary on of drive causing SAC 71. Need to add changes (DDC\LDC\LBI boot \appl code problem 313 code) to 320 code. 3592 drive modules power supply diags for the 4th drive bay do not work properly. S10K 314A FW does not identify media type and usage. 3592 short media returns an incorrect media character through SCSI read element status. Code can take the library offline and not post an error. When varying a drive offline the library does not queue a unit attention until the menu is exited. [. . . ] NOTE: Do not use Main Menu SetupCleaningMedia to perform this operation. This operation inserts the cartridges into the library database only. Known Issues 5 Release Notes Document 6-00016-32 Rev A September 2007 Change Request Number 41305 Service Request Number Description The usage count for the first cleaning cartridge increments when a second cleaning cartridge is used. Workaround Make sure that cleaning cartridges are inserted into the library by using the Insert Clean Tape command (Main MenuCommands Insert/ EjectInsert Clean Tape). This operation physically inserts the cartridges and also inserts them into the library database. NOTE: Do not use Main Menu SetupCleaningMedia to perform this operation. [. . . ]