User manual QUANTUM SCALAR I2000 I6.6 RELEASE NOTES 09-2009

[. . . ] Release Notes Product Operating Systems (Remote LMC Client) Date Scalar i2000® 595A. GS01601 MicrosoftTM Windows®, AIX®, HP-UXTM, SolarisTM, and Red Hat® Linux September 2009 Contents 0 Purpose of This Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 New Features and Enhancements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Compatibility and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Resolved Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Problem when either label is misread and we get more than one label mapped to a slot, or when position of label is incorrect and mapped to an adjacent (and full) slot. 20856 20858 923844 964268 Cartridge Outside Boundaries. Only log E_CELL_CARTRIDGE_OUTSIDE_SLOT_WINDOW and E_MAGAZINE_CART_OUTSIDE_BOUNDARIES since a single slot scan has been implemented (20856) that resolves what is in a slot. Other tickets are posted if there is a problem within the slot (i. e. E_GRP_REACH_HOME_FAILED ticket is posted when no problem is found. To reduce this ticket the reach axis is now calibrated. Drive Comm Warning - change E_DDC_DP_DRIVE_COMMS_WARNING and E_DDC_DP_DRIVE_COMMS_FAILED events to 'informational only' so that they don't cause tickets. The RCU should not try to open a file, for writing, on the MCB more than one time. Add a check to make sure the number of entries read from the file makes sense before using the file. Removed "Statusmonitor not alive" ticket. 20870 20904 20921 20923 20924 864458 903678 914416 955072 930828 959496 898460 898460 MCB Comm Problem with RCU SOIP. 20931 20932 20997 21007 21035 21052 21069 SNMP thread issue does not allow the AMC/LMC to become ready after power cycle/ reboot. Problems in Status Monitor caused FCBs to start up and auto level slowly. Tune the I/E DLT get pattern to be more reliable and provide support for an optional DLT cleaning station. DVT19 failure getting tapes from SDLT600 drives. An analysis of the SDLT600 and 320 drive get operation found that the get position should be lowered by 1. 5mm and the put position lowered by 1. 0mm. Duplicate entries in fibre channel controller node name list- Capture Side. 21557 21696 21737 22540 22633 902482 902482 902482 Fixed block data transfer > 2M not rejected properly >2M transfer allowed with fixed block mode write/read. Read buffer (descriptor) returns buffer size > 2M. Snapshot (Extended) is not Complete. 8 Resolved Issues Release Notes Document 6-00424-44 Rev B September 2009 Known Issues This release of Scalar i2000 firmware has the following known issues. This list contains cumulative information for all previously released Scalar i2000 library versions. 0 Change Request Number 24444 Service Request Number Description SNMP v3 is not functioning due to "unknown user" issue. Workaround Change the SNMP password to a temporary password, and then change the temporary password to back to the desired password. Make sure the robot is in frame six or less before pushing the Robotics Enabled button. 22726 On a seven frame or larger library, after closing the door and enabling the robotics, the robot performs normal going ready operations like homing, scanning any closed IE stations, etc. but the library never goes online and ready after the robot stops moving. LTO-4 drive not presented to host, issue with loop id. 21695 Two workarounds available: **Set the drive to use Soft Loop ID. **Set the blades port for this target channel to Hard ID 0 to match that of the drive. However, it will be necessary to telnet to the blade and enter the 'fcRestart' for this channel for the ID change to take effect. [. . . ] While performing Update Software, the library hung during power up. 304086 312136 AMC should use 802. 3 standard to determine valid external IP and gateway addresses FCB eVPS map was corrupted. 304492 42326 33779 33714 12 Known Issues Release Notes Document 6-00424-44 Rev B September 2009 Change Request Number 33306 Service Request Number Description Reservations not transferred when host port fails over. Workaround When the FC ports fail over the host needs to re-login (PLOGI + PRLI) to the FCB. Re-login requires that reservations be re-established. [. . . ]