User manual QUANTUM SDLC 2.7 INSTALLATION FOR SCALAR 10K 09-2007

[. . . ] Scalar ® Distributed Library Controller TM 2. 7 Installation Guide Scalar Distributor Library Controller Reference Guide, 6-00659-04, September 2007, Made in USA. Quantum Corporation provides this publication "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties of merchantability or fitness for a particular purpose. Quantum Corporation may revise this publication from time to time without notice. COPYRIGHT STATEMENT Copyright 2007 by Quantum Corporation. [. . . ] If not, cancel the operation, move Cluster group ownership to the current node, and start Add/Remove engine again. CAUTION Note Before removing Scalar DLC software from any cluster node, launch SDLC Cluster Configurator and remove cluster configuration from the Scalar DLC resources (Remove button). Note Local administrator rights are required to execute this procedure. Domain administrator rights are required if the Scalar DLC is installed under domain account and/or as the failover or self-domain solution. Note The additional Repair instructions can be found at Renaming and Repair on page 93. Additional upgrade instructions can be found at Upgrading the Scalar DLC on page 82. Installation Guide 77 Figure 40 Starting the Scalar DLC Add/Remove Click Next to proceed to the following screen. Figure 41 Modify/Repair/Remove Specify the activity type and click Next to proceed. Remove CAUTION After removing the Scalar DLC software, always remove its SCSI Target drivers, too. See Add/Remove SCSI Target Drivers on page 122. The Remove process deletes all of the Scalar DLC software features except for the Scalar DLC account name and password that were set up during installation. For installation information, refer to Installing the Scalar DLC on page 51 78 Upgrade, Remove, Repair Figure 42 Saving the Database The Scalar DLC database can be either removed, or saved for future use. Click Next to proceed to the remove and the final screen. Software programs such as Java 2, MS IE, MSDE 2000, and so forth, are not removed and should continue to function normally. The Remove process also restores the old web server configuration software. Note To remove the required Scalar DLC software packages, use Control panel > AddRemove Programs. Repair The Repair process allows the user to repair the damaged Scalar DLC configuration without re-installing the software. Figure 43 Repair Options Installation Guide 79 Choose either the Server option to repair damaged Scalar DLC software components (see Server on page 80), or Database option to repair the damaged Scalar DLC database (see Database on page 81). Click Next to proceed. Server The Repair Scalar DLC Server process allows you to re-register the Scalar DLC software components under new user account without re-installing them. This section has been added to avoid problems concerning the changes of user account name/password. This section also allows to repair the installed Scalar DLC software after the PC is renamed. Figure 44 Repair Server Options Select the repair options and click Next to proceed. Table 15 Name Computer renaming Repair user account Repair Options Operation Check Check Description Repair the Scalar DLC software after the computer has been renamed. The Scalar DLC user account is also repaired. Repair the damaged Scalar DLC user account. See User Account on page 80. If the Computer renaming mode is selected, the Repair checks all needed software components. If no software upgrade is needed, the Repair process proceeds to the user account section. See User Account on page 80. User Account The repair user account screens look exactly the same as the user account creation screens appear during the Scalar DLC installation. See Figure 21 on page 58 for the local account, and Figure 22 on page 59 for the domain account. See Table 6 on page 59 for the user account settings. 80 Upgrade, Remove, Repair Note To repair the Scalar DLC installed under a domain account, the domain administrator rights are required. If the account name already exists and the password does not match the existing account's password, the User Account warning appears. [. . . ] Set up the web browser(s) according to the corporative security standards. If the email client will be used on the same PC where the Scalar DLC is installed, ensure it is secured too (for example, binary files are not automatically opened, etc. ). Contact the local network administrator for the details. Step 2 Step 3 Step 4 Note If the firewall is used to secure the Scalar DLC host, the DAS client software must be installed with the firewall support. Refer to Installing DAS Client on page 71. Installation Guide 143 Antivirus Strategy To ensure the Scalar DLC system remains virus-proof and worm-proof, perform the following security actions. [. . . ]