User manual RADIOSHACK 2-IN-1 UNIVERSAL REMOTE CONTROL

[. . . ] 2-in-1 Universal Remote Control Owner's Manual Please read before using this equipment. X Contents Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you cannot find the correct code, try performing a manual search (see "Manual Code Search" on Page 10). Hold down P until the red light blinks twice, then enter the 4-digit manufacturer's code for the desired device. When the red light blinks twice, the remote control has accepted the code. For example, to set up the remote control of a Panasonic TV (manufacturer's code 0051), press TV, hold down P until the red light blinks twice, then press 0 0 5 1. 6 Preparation Note: If you entered the code incorrectly, the red light blink once. Point the remote control at your TV (or cable converter) and press POWER. If the remote does not operate your device, try the other codes listed in "Manufacturers' Codes" on Page 12 for your brand of TV or cable converter. You can also search to find a working code (see "Manual Code Search" on Page 10). Repeat Steps 2­5 to program the other device (cable converter or TV). Preparation 7 X Operation The command keys on the remote control work the same way as their counterpart keys on the original remote controls. However, they might be labeled differently. Point the remote control at the device you want control and press its device key (TV or CBL). Repeat Steps 1 and 2 for the other device you want to operate. To turn off the last device you selected, press POWER. To turn off the remaining device, press its device key, then press POWER. CONVERTING THE CBL KEY If you are not using CBL, you can reprogram it to operate a second TV. Reassigning the CBL Key 1. Hold down P until the red light blinks twice. The red light blinks twice to indicate successful programming. Program the converted CBL key with the code for the second TV (see "Setting Up Your Remote Control" on Page 6). Now each time you press CBL, you can control the second TV by pressing the desired function keys. 8 Operation Restoring the CBL Key When you are finished using your second TV, you can restore the CBL key to control a cable converter. Hold down P until the red light blinks twice. The red light blinks twice to indicate successful programming. USING VOLUME LOCK Volume Lock is preset so that pressing VOL+/­ or MUTE only controls your TV's volume, even if you press CBL. If your cable converter has a volume control, you can change this setting to add control of the cable converter's volume. Setting Volume Lock To Cable Converter 1. Hold down P until the red light blinks twice. To control your cable converter's volume, press CBL then VOL +/­. Resetting Volume Lock To TV 1. [. . . ] · Replace the batteries. CARE Keep the remote control dry; if it gets wet, wipe it dry immediately. Use and store the remote control only in normal temperature environments. Handle the remote control carefully; do not drop it. Keep the remote control away from dust and dirt, and wipe it with a damp cloth occasionally to keep it looking new. [. . . ]