User manual RADIOSHACK 4-IN-1 LIGHT-UP REMOTE

[. . . ] 4-in-One Light-Up Remote Owner's Manual Please read before using this equipment. ^ Contents Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 A Quick Look at the Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Hold down P until the remote's red light blinks twice, then release P. Enter the first 4-digit manufacturer's code for the desired device. When the red light blinks twice, the remote control has accepted the code. For example, to set up the remote control of a Panasonic TV (manufacturer's code 0051), press TV, hold down P until the red light blinks twice, then release P and press 0 0 5 1. Note: If you entered the code incorrectly, the red light emits one long blink. Point the remote control at the desired device and press POWER. If the remote control does not operate your device, try the other codes listed in "Manufacturers' Codes" on Page 20 for your brand of device. Otherwise, use the search method to find a working code -- see "Manual Code Search" on Page 17. Repeat Steps 3­5 to program other devices. Note: If the remote control does not operate all device functions, try using another code in the list that may be more compatible. PROGRAMMING FAVORITE CHANNEL SCAN Once they have been programmed into a favorite channel table, you can scan up to ten favorite channels for a desired device. Note: Once you have programmed SCAN/FAV for Favorite Channel Scan, you cannot use it for Channel Scan unless you reset it (see "Resetting Scan" on Page 10). Preparation 9 1. Select either TV or CBL/SAT for the favorite channel scan. Hold down P until the red light blinks twice. Enter a desired two-, three-, or four-digit channel number (for example, 050 or 0500), depending on your device. If you entered a two- or three-digit channel number, you must next do one of the following: · If your original remote requires you to press Enter or Select to send a command, then do so after entering the digits of your favorite channel. · If your original remote does not require you to press Enter or Select to send a command, then after entering your two- or three-digit channel number, press P. If you entered a four-digit channel number, do not press P. 5. Repeat Step 4 up to nine more times to store another favorite channel for the same device, or exit the program by pressing P until the red light blinks twice. Note: Upon entering the tenth channel, the remote exits favorite channel programming. Programming Favorite Channel Scan for a second device deletes the programming for the first. Resetting Scan Once you have programmed SCAN/FAV for Favorite Channel Scan, you cannot use it for Channel Scan unless you reset it. Hold down P until the red light blinks twice. 10 Preparation 3. You can now use the remote for Channel Scan (see "Using Channel Scan" on Page 14). Hold down P until the red light blinks twice. PROGRAMMING MACROS Your remote has four macro keys (MUSIC, MOVIE, SPORT, and NEWS) that you can use to store up to three channels per macro key for instant tuning of TV or cable/ satellite channels. For example, if your favorite sports channel on your cable service is 061, you can store it as an instant tune-in macro. [. . . ] Use and store the remote only in normal temperature environments. Handle the remote carefully; do not drop it. Keep the remote away from dust and dirt, and wipe it with a damp cloth occasionally to keep it looking new. Modifying or tampering with the remote's internal components can cause a malfunction and might invalidate its warranty. [. . . ]