User manual RADIOSHACK 6-IN-1 REMOTE CONTROL WITH LIGHTED KEYPAD

[. . . ] 15-1923. fm Page 1 Monday, July 19, 1999 12:41 PM Cat. 15-1923 OWNER'S MANUAL 6-in-1 Remote Control with Lighted Keypad Plug 'n Power® Compatible Please read before using this equipment. 15-1923. fm Page 2 Monday, July 19, 1999 12:41 PM FEATURES Your RadioShack 6-in-1 Remote Control can replace up to six infrared remote controls. You can use it to control your TV, VCR, cable box, satellite receiver, and even lights and appliances with Plug 'n Power modules (not included). All you have to do is tell it which TV, VCR, or other components' remote controls you want to replace (by entering 3-digit codes). [. . . ] Set the house code dial on top of the IR command console to the same letter as your Plug 'n Power modules. Set the selector switch on the IR command console for the group of modules you want to control (1­4 or 5­8). Need help?Call 1-800-989-4706 13 15-1923. fm Page 14 Monday, July 19, 1999 12:41 PM 5. Hold down SET UP on the 6-in-1 until the red light above turns on. Press Plug 'n Power, then enter 0 ­ 1 ­ 4 on the 6-in-1. To turn on all light and appliance modules set to the same house code as the IR command console, press POWER (All Lts On) on the 6in-1, or ALL LIGHTS ON on the IR command console. To turn off all light and appliance modules set to the same house code as the IR command console, press MUTE (All Off) on the 6-in-1, or ALL UNITS OFF on the IR command console. To turn specific lights and appliances on or off using the 6-in-1 Remote Control, press the digit key (1, 2, 3, 4, 5, 6, 7, or 8) for the module you want to control. Then press On or Off (CHANNEL + (On) or CHANNEL ­ (Off)). To control specific lights and appliances directly from the IR command console, set the console's selector to the number of the module you want to control (1­4 or 5­8), press the button on the console that corresponds to the number of the module you want to control (1/5, 2/6, 3/7, 4/8), then press ON on the IR command console. To brighten or dim lights connected to lamp and appliance modules, press the digit key for the module you want to control. Then hold down VOLUME + (Brt) or VOLUME ­ (Dim) on the 6-in-1. Release the key when the desired level of brightness is reached. Note: You must select the individual light to brighten or dim even if you used POWER (All Lts On) on the 6-in-1 to turn on all the lights at the same time. Need help?Call 1-800-989-4706 14 15-1923. fm Page 15 Monday, July 19, 1999 12:41 PM Controlling Lights and Appliances Using a Control Center Module Follow these steps to control Plug 'n Power modules with your 6-in-1 using your Plug 'n Power Wireless Remote Control System's control center module. Plug the control center module's power cord into any standard AC outlet. Set the house code dial on top of the control center module to the same letter as your Plug 'n Power modules. Set the unit selector switch on the control center module for the group of modules you want to control (1­8 or 9­16). Note: If the 6-in-1's Plug 'n Power code is already set to 0 ­ 1 ­ 3 (the default), skip Steps 4 and 5. Hold down SET UP on the 6-in-1 until the red light above turns on. Press Plug 'n Power then enter 0 ­ 1 ­ 3 on the 6-in-1. On the 6-in-1, enter the house code that matches your control center module's house code (see Step 3 under "Entering a Plug 'n Power House Code" on Page 13). [. . . ] Do not use harsh chemicals, cleaning solvents, or strong detergents to clean it. Modifying or tampering with the 6-in-1's internal components can cause a malfunction and invalidate its warranty. If your 6-in-1 is not performing as it should, take it to your local RadioShack store for assistance. Need help?Call 1-800-989-4706 41 15-1923. fm Page 42 Monday, July 19, 1999 12:41 PM SPECIFICATIONS Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]