User manual RADIOSHACK Z-707 BATTLE IRON CLAW

[. . . ] 7 Device Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Setting Up Your Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Programming Favorite Channel Scan . . . . . . . . . . . . . . . 10 Resetting Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For example, to set up the remote control of a Panasonic TV (manufacturer's code 0051), press TV, hold down P until the red light blinks twice, then press 0 0 5 1. Note: If you entered the code incorrectly, the red light emits one long blink. Point the remote control at the desired device and press POWER. If the remote control does not operate your device, try the other codes listed in "Manufacturers' Codes" on Page 25 for your brand of device. Otherwise, use the search method to find a working code (see "Using Manual Code Search" on Page 23). Repeat Steps 2­5 to program other devices. Note: If the remote control does not operate all device functions, try using another code in the list that may be more compatible. PROGRAMMING FAVORITE CHANNEL SCAN Once you have programmed channels into a favorite channel table, you can scan up to ten favorite channels for a desired device. Note: Once you have programmed SCAN/FAV for Favorite Channel Scan, you cannot use it for Channel Scan unless you reset it (see "Resetting Scan"). Select TV or CBL/SAT for the favorite channel scan. Hold down P until the red light blinks twice. The red light blinks twice. 10 Preparation 4. On the device's remote control, hold down the key to be learned until the red light on the 6-In-One Remote blinks twice. If the red light does not blink twice, repeat Steps 1­ 5. To learn functions on another key, repeat Steps 3­6. To lock in learned functions on the 6-in-One Remote, hold down P until the red light blinks twice. To test a learned function, press the learned key on the 6-In-One Remote and use the function as usual. Deleting a Learned Function 1. Hold down P until the red light blinks twice. Press the device key that corresponds with the desired device's remote (TV, VCR, CBL/SAT, DVD, or AUX). Press the Smart key (1S, 2S, 3S, or 4S) for the learned function you want to delete twice. To clear functions stored on other Smart keys, repeat Steps 1­4. X Operation Note: The command keys on the 6-In-One Remote work the same as the keys on your original remote controls. However, the labeling may be different. Operation 15 USING THE REMOTE Once you have completed all the programming for the remote (see "Preparation" on Page 7), you are ready to use your 6-In-One Remote. Point the remote at the desired device and press the device key (TV, VCR, CBL/SAT, DVD, CD, or AUX). [. . . ] Note: The red light will not blink if the code digit is a "0". Repeat Step 4 three more times for each successive digit by pressing and releasing 2, 3, and 4. X Troubleshooting If the remote control stops working after you have successfully tested the control for each device, or if you are unable to get the remote control to work at all, do the following: · Be sure you press the device key for the device you want to control before you press any other key. · Confirm that your IR devices are working properly by using the original remote control or the manual controls. If you have any other problems, call customer service at 888-631-9859. CARE Keep the remote dry; if it gets wet, wipe it dry immediately. [. . . ]