Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual RANE KDC 6. We hope that this RANE KDC 6 user guide will be useful to you.
Lastmanuals help download the user guide RANE KDC 6.
You may also download the following manuals related to this product:
RANE KDC 6 DATASHEET (140 ko)
Manual abstract: user guide RANE KDC 6
Detailed instructions for use are in the User's Guide.
[. . . ] #2 phillips screwdriver #1 phillips screwdriver small blade screwdriver needle nose pliers diagonal wire cutters
I/O Panel Exchange Procedure:
1. Unplug the MA 6S from the AC power source. IMPORTANT: Wait ten (10) minutes before starting the installation of the KDC 6 for the power supply caps to safely discharge. [. . . ] Confirm that the MA 6S is off and unplugged, and the I/O panel exchange is completed. Referring to the included diagram (see drawing number 522-223), connect the wires from the KDC 6 to the correct locations on the MA 6S. Orient the KDC 6 with the component side of the PCB facing up (towards the bottom cover) while doing this. After all wires are connected correctly to the power supply PCB of the MA 6S, install the KDC 6 into the MA 6S chassis with the 3-station Euroblock connector protruding out the rear of the chassis. The components of the KDC 6 circuit PCB should be facing up (towards the bottom cover). Make sure the holes in the chassis of the MA 6S align with the threaded holes on the L-brackets of the KDC 6 and install (2) 4-40 x ¼" screws through the chassis into the L-brackets. Using the included plastic tie-wraps, bundle the wires of the KDC 6 neatly and route them away from any sharp objects. Reinstall the bottom cover using the (16) screws removed in step 4 of the I/O panel exchange procedure. You are now done with installing the KDC 6. See the next section on power supply connection. continued on back page
Connecting the KDC 6 to Your 48VDC (+24VDC) Power Supply:
1. Confirm that the MA 6S unit is off and unplugged. The KDC 6 must be powered from a 48VDC power supply with a center tap to allow +24VDC operation. Refer to the following diagram using four automobile batteries. Two 12V batteries connected in series equal 24 volts. Note that all wires used must be 10-12AWG. You should always use fuses when utilizing automobile batteries. These batteries are capable of supplying large amounts of current and can explode if shorted.
3. [. . . ] Connect the wire from the common of your supply to the COM Input of the KDC 6. Once all wires are connected to the KDC 6 and the unit is connected to the 48VDC ( +24VDC) power supply, the fan in the MA 6S will begin to turn and the POWER LED lights. After a short period of time the output relays of the MA 6S pick up. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE RANE KDC 6
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual RANE KDC 6 will begin.
RANE KDC 6 DATASHEET (140 ko)
