User manual RAYMARINE G170

[. . . ] Raymarine Sunlight Viewable Marine Displays Users Guide Document Number: 81277_1 Date: August 2006 Trademarks and registered trademarks Autohelm, HSB, Raymarine, RayTech, RayTech RNS, Sail Pilot, SeaTalk and Sportpilot are registered trademarks of Raymarine Limited. Apelco is a registered trademark of Raymarine Holdings Limited (Registered in all major marketing territories). AST, Autoadapt, Auto GST, Autoseastate, Autotrim, Bidata, Marine Intelligence, Maxiview, On Board, Raychart, Raynav, Raypilot, Raystar, ST40, ST60, Seaclutter, Smart Route, Tridata and Waypoint Navigation are trademarks of Raymarine Limited. All other product names mentioned are trademarks or registered trademarks (if applicable) of their respective companies. [. . . ] Connect all cables as required - see "Rear connections" on this page. * The selector switch enables you to switch between the SeaTalkhs/ Ethernet and Serial port connections. 18 Raymarine Sunlight Viewable Marine Displays - Users Guide Operation 19 Operation VGA 1/Menu VGA 3/Scroll UP DVI 2/Scroll RIGHT Composite Video 2/ Brightness S-Video/ Enter POWER VGA 2/ Scroll DOWN DVI 1/Scroll LEFT Composite Video 1/ PIP Composite Video 3/ Night mode Introduction Your Raymarine Sunlight Viewable display can be controlled using the On Screen Display (OSD) menu and/or the 10 buttons on the front bezel of the unit. The OSD menu enables you to change the way in which your display is set up and is accessed using the Menu button. Power Power ON To power your monitor ON press and hold the POWER button for 3 seconds. Power OFF To power your monitor OFF press and hold the POWER button for 3 seconds. Pressing the power button will display a list of what input for the main screen is associated with each button. This is just a reminder and is not part of the input selection process. Using the buttons Each of the 10 buttons on the front bezel of your display has an input and a control function. Input functions enable you to select the type of signal input to the display. Control functions enable you to change the appearance of the display. 20 Raymarine Sunlight Viewable Marine Displays - Users Guide Below the tab, the function it controls is named and its sub-menu is shown. OSD menu The OSD menu enables you to change the appearance of your on-screen display. Press and hold the Menu button, the OSD appears. Navigating the OSD As a general rule you can navigate through the OSD menu using the following button presses: Menu 1. Press the Menu button to move between the 7 tabs. Tabs are highlighted from left to right. When the last tab is highlighted, the next press will return to the first tab. Press to move to exit a sub-menu and move to the tab layer of the menu. Press either of these buttons to switch between tabs. You can move backwards and forwards as required. Press these buttons to toggle a sliding bar for an attribute in the sub-menu. Press this button to enter the sub-menu of the highlighted tab. Left/ Right Control tab Sub menu Control name There are 7 function tabs across the top of the OSD, from left to right: · · · · · · · Video input. Input naming. Down Operation Up/ Down 1. Press these buttons to move up or down within the sub-menu. When you reach the bottom, pressing the Down button returns to the top of the sub-menu. After changing an attribute of the sub-menu, use these buttons to move to the next attribute. · · · 2 x DVI inputs. 1 x S-Video input. 21 PIP The Picture-in-Picture (PIP) feature of the display enables you to set up a second input and show the associated image in a picture inset within the main display screen. [. . . ] PIP Press and hold - PIP Input mode is selected. Each press of a button will change the video input in the PIP window. Press and hold ENTER to exit PIP Input mode. The PIP remains open with the last input source selected. [. . . ]