User manual RAYMARINE HSB2 PLUS 10 INCH CRT

[. . . ] hsb2 PLUS Series CRT Display Owner's Handbook Document number: 81187_3 Date: September 2002 Preface iii hsb2 PLUS Series CRT Display Owner's Handbook September 2002 INTENDED USE The display units detailed in this handbook may form part of navigational radar systems intended for light marine use. These displays and radar systems are only an aid to navigation. SAFETY NOTICES This radar equipment must be installed and operated in accordance with the instructions contained in this manual. Failure to do so can result in personal injury and/or navigational inaccuracies. The CRT display unit and scanner unit contain high voltages. [. . . ] To edit the symbol, press the SYMBOL soft key. Use the soft keys, shown in the following illustration, to highlight the required symbol, then press ENTER to confirm the selection. Press ENTER or CLEAR to return to the default soft keys. SELECT SYMBOL D4178-1 4. To edit the waypoint name, press the NAME soft key. Use the trackball to enter or edit the name: Use the left or right side of the trackball to move the cursor to the character you wish to change. Use the top or bottom of the trackball to scroll through the characters. When you have finished editing the name, to remove the window, press ENTER to save the name or CLEAR to cancel the operation. The waypoint name replaces the waypoint number. Press ENTER or CLEAR to return to the default soft keys. Editing the Waypoint Details 5-14 hsb2 PLUS Series CRT Display EDIT WAYPOINT 5. To edit the waypoint position, press the EDIT WAYPOINT soft key, followed by POSITION. The Waypoint Position pop-up is displayed. Use the soft keys to select LAT, LON, BRG or RNG. Use the trackball to edit the value: Use the left or right side of the trackball to move the cursor to the character you wish to change. Use the top or bottom of the trackball to scroll through the characters. Adjust each parameter until the waypoint position is correct. When you have finished editing the position, press ENTER to save the position or CLEAR to cancel the operation. Press ENTER or CLEAR again, the Waypoint Position window is removed from the screen and the default soft keys are displayed. Erasing a Waypoint Erasing a Waypoint You cannot erase the target waypoint or waypoints that are used in routes. However, you can remove a waypoint from the current route - see Editing a Route on page 5-27. If you try to erase a waypoint that is used in a saved route you are warned "WAYPOINT IS USED IN A ROUTE & CANNOT BE DELETED" To delete a waypoint using the cursor: WPT 1. Move the cursor over the waypoint, until the letters WPT are displayed. The waypoint is removed from the screen and the Waypoint List is updated. Note: If you have stopped a GOTO (see Stop Follow or Stop Goto on page 5-33), the target waypoint remains displayed as a target; you need to use the CLEAR GOTO soft key before you can erase the waypoint using the cursor. [. . . ] The Installed Warranty provides for onboard repair or exchange, by Raymarine or it's approved service agents, for a period of 2 years/24 months, from date of sale of the boat to the end user ­ where the equipment has been installed by a Raymarine certified installer, or from commissioning of the installation by a Raymarine certified installer, or 30 months from date of shipment of the equipment from Raymarine ­ whichever expires first, except as provided below. Obtaining Warranty Service In the event of Warranty service being required, contact Raymarine or the nearest Raymarine certified service agent ­ a full list of local service agents are available on the Internet or can be requested from the nearest Raymarine agent. A suitable proof of purchase, showing date, place of purchase, and serial number must be made available to Raymarine or authorized service agent at the time of request for Warranty service. In cases where a Raymarine certified installer has not installed the product; i. e. Limited Warranty, the affected unit must be returned to the local Raymarine approved service agent, with a copy of proof of purchase and/or completed warranty card. [. . . ]