User manual RAYMARINE HSB2 PLUS FISHFINDER

[. . . ] hsb2 PLUS Series Fishfinders Owner's Handbook Document number: 81195_2 Date: August 2002 hsb2 Plus Series Fishfinders iii hsb2 Plus Series Fishfinders Owner's Handbook August 2002 Intended Use Raymarine hsb2 Plus Series Fishfinders are intended for recreational fishfinding. The combined Fishfinder/Chartplotter devices are intended for recreational fishfinding and course chartplotting. The optional chartplotter function is intended as an aid to navigation and should not be relied upon as a substitute for official navigation charts. SAFETY NOTICES This equipment must be installed and operated in accordance with the instructions contained in this manual. Failure to do so can result in personal injury and/or navigational inaccuracies. [. . . ] When you have set all the controls to the levels you require, press ENTER or CLEAR to return to the default display. 25% STC MULTI GAIN GAIN ADJUST 200 50 Chapter 4: Fishfinder Operations 4-7 4. 3 Fishfinder Data Window The Fishfinder can display various measurements in large format data boxes. Use the DISPLAY key options to select a data window that is vertically split with the full-screen fishfinder display. Three data windows are available, each window provides several large-format data boxes for specific information as follows: Data Window A AUTO G RZ Data Window B Data Window C 50kHz 81°06^34W 28°17^07N F 20. 1 15. 1 Rng 2. 95nm Brg 093°T COURSE OVER GROUND 20 COURSE OVER GROUND CURSOR BRG 099oR 30 MINUTES 0 RNG 2. 410nm SPEED 10. 1 T T SPEED OVER GROUND 40 SPEED OVER GROUND kts DEPTH kts kts DEPTH 60 DEPTH M FREQUENCY ZOOM ft BTM. LOCK 80 A-SCOPE ft ft D5018-4 Figure 4-3: Fishfinder Data Windows · Data Window A ­ provides surface temperature with a 30 minute temperature graph, speed through water and depth. · Data Window B ­ provides position, course over ground (COG), speed over ground (SOG) and depth. · Data Window C ­ provides waypoint range and bearing, course over ground (COG), speed over ground (SOG), and depth. The data boxes display information in the units selected in system set up (see Section 7. 3). Fishfinder Data Window 0 POSITION WAYPOINT 4-8 hsb2 Plus Series Fishfinders 4. 4 Using Alarms ALARMS MULTI The ALARMS key is used to set up alarms; three alarms are available to alert you of fish, shallow water and deep water. Each alarm can be toggled ON and OFF, and you set the depth at which shallow and deep water alarms are triggered (between the ranges 2­3000 feet/0. 5­500 fathoms/1­1000 meters). You may want to use the shallow and deep water alarms when you are anchored. Set the limits to just above and below your anchor depth; the Fishfinder triggers an alarm if the anchor drags and the boats moves into shallower or deeper water. Using Alarms · Fish Alarm ­ If this alarm is ON the unit sounds a buzzer whenever it finds a fish. Different buzzer tones are used to indicate fish detected by the 50 kHz and 200 kHz frequencies. · Shallow water ­ You set depth at which the shallow water alarm triggers. When the depth is less than that set, the buzzer sounds and a pop-up window describing the alarm is displayed. You cannot set the shallow alarm to be deeper than the deep alarm. · Deep water ­ You set depth at which the deep water alarm triggers. When the depth is more than that set, the buzzer sounds and a pop-up window describing the alarm is displayed. You cannot set the deep alarm to be shallower than the shallow alarm. After you have acknowledged the sounding of a deep water alarm, a minimum of 30 seconds must elapse before a another depth alarm can sound again. The top line status bar shows the condition of the alarms: · indicates an alarm is enabled. The speaker symbol is unfilled until an alarm is triggered and silenced, then the symbol is shown solid. · S indicates the shallow alarm is enabled; a pop-up window indicates when the alarm is triggered. · D indicates the deep alarm is enabled; a pop-up window indicates when the alarm is triggered. · indicates the fish alarm is enabled. External Alarms All SeaTalk system alarms (except autopilot, shallow and deep) alarms are received and displayed on the Fishfinder. You can silence these alarms by pressing any key. No other action is taken by the Fishfinder except to silence the alarm. Chapter 4: Fishfinder Operations 4-9 To set an alarm 1. The alarms soft keys are displayed. FISH ALARM OFF ON SHALLOW ALARM DEEP ALARM D5031-1 ALARMS 3. [. . . ] To connect your Differential Beacon Receiver, you must cut off the 5-pin connector, strip back the insulation on all the wires, and connect to the Auxiliary Junction Box as shown in the second illustration below. CAUTION: Ensure the correct polarity of the 12 V supply before applying display or SeaTalk power. It is recommended that a multimeter is used to check the connections. To Display Unit SeaTalk Socket Black Red Green Yellow White Brown From GPS sensor Black 12V Power Supply (fused) Red D4297-3 To Display Unit SeaTalk Socket Black Red Green Yellow White Brown From GPS sensor Black 12V Power Supply (fused) Red Black Red Yellow White Green From the DBR D4298-3 Appendix B: Using the Auxiliary Junction Box Autohelm GPS, Z260 and Z273 B-4 hsb2 Plus Series Fishfinders Raystar 112LP (SeaTalk version) To connect your Raystar 112LP to your Fishfinder, refer to the first illustration below or follow the instructions in Chapter 2. To connect the Raystar 112LP and your Differential Beacon Receiver, cut off the 5-pin connector and strip back the red, black, and green wires. [. . . ]