User manual RAYMARINE NAV398

[. . . ] Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company. NAV398GPS/IL>RAI\l GPSlLORAN OPERATION MANUAL i Table of Contents Page SECTION 1 INTRODUCTION 1 . O General 1. 1 About This Manual SECTION 2 INSTALLATION 2. 0 General 2. 1 Unpacking and Inspection 2. 1. 1 Equipment Supplied 2. 2 Display Installation 2. 2. 1 Choosing a Location 2. 2. 2 Mounting the NAV Unit 2. 2. 3 Flush Mounting 2. 3 Electrical Connections 2. 3. 1 Power Input 2. 3. 2 Sensor Connections 2. 3. 3 Interface to External Navaids 2. 3. 4 Ground Connection SECTION 3 OPERATION 3. 1 General 3. 2 The Keyboard 3. 3 Basic Operations 3. 3. 1 Turning the Unit ON/OFF 3. 3. 2 Contrast/Backlighting Level 3. 3. 3 Auto Start-up 3. 3. 4 Selecting Loran/GPS Mode 3. 4 Initializing Sensors 3. 4. 1 Estimated Latitude 3. 4. 2 Estimated Longitude 3. 4. 3'The Status Page 3-1 3-1 3-3 3-3 3-3 3-3 3-4 3-5 3-6 3-6 3-7 2-l 2-l 2-l 2-2 2-2 2-3 2-3 2-4 2-5 2-5 2-6 2-7 l-l l-l 3. 5 Main Display Modes 3. 5. 1 Position Display Mode 3. 5. 2 Customizing Display Modes 3. 5. 3 Navigation Display Mode 3. 5. 4 CD1 Display Mode 3. 5. 5 Plot Display Mode 3. 5. 6 Simulator Mode 3. 5. 7 Display Mode Operations 3. 5. 7. 1 Saving Events 3. 5. 7. 2 GOT0 Destinations 3. 6 Entering Waypoints 3. 6. 1 General Waypoint Information 3. 6. 2 Waypoint Directory 3. 6. 3 Naming Waypoints 3. 6. 4. . Storing Waypoints 3. 6. 4. 1 Entry by L/L 3. 6. 4. 2 Entry by TDs 3. 6. 4. 3 Entry by Bearing/Distance 3. 6. 5 Waypoint List Operations 3. 6. 5. 1 Selecting Waypoints 3. 6. 5. 2 Editing Waypoints 3. 6. 5. 3 SF Operations 3. 7 Setting Alarms 3. 7. 1 Arrival Alarm 3. 7. 2 Anchor Alarm 3. 7. 3 Off-Course Alarm 3. 8 Man-Overboard Mode 3. 9 Route Plans 3. 9. 1 Make a Route 3. 9. 2 Following Route Plans 3. 9. 3 Editing Route Plans 3. 9. 4 Erasing Route Plans 3. 10 The Menu Key 3. 10. 1 Main Menu Directory 3. 10. 2 Signal Status Pages 3-8 3-8 3-11 3-l 1 3-12 3-13 3-16 3-16 3-16 3-17 3-19 3-19 3-19 3-21 3-22 3-22 3-23 3-24 3-24 3-25 3-25 3-25 3-27 3-27 3-28 3-29 3-29 3-30 3-31 3-32 3-33 3-34 3-35 3-35 3-36 _ _ . . -. --. --- SECTION 1 INTRODUCTION 1 . O General Congratulations on selecting Raytheons' NAV 398 for Loran-C/GPS navigation aboard your vessel. We are sure you will enjoy using this ultra modern, full function, and compact navigation system. [. . . ] Copying Waypoints Waypoints can easily be transferred from one memory location to another using the COPY feature. To Copy waypoints: Press them softkey on the Waypoint List. On the Waypoint- SF menu press ICOPYIMEASURE WPTSl softkey. Then type the waypoint # (from) and press-1 Then press the waypoint # (to) and press (ENTERI again. Measuring between Waypoints You can easily measure the bearing and range between any two waypoints stored in memory by pressing the/ COPY/MEASURE WPTS~ soflkey on the WAYPOINT - SF screen. WAYPOINTS screen appears, press thelMEAS. lsoft- key. Then type the number of the "FROM" waypoint and -1 followed by the number of the "TO" waypoint. l c u l a t e d The ca bearing and range will then be displayed. If you want to measure additional points, press the-1 softkey again. The Fr and To digits will clear and you may re-enter a new pair of numbers. Press Fj?[for the new Bearing/Range calculation. Pressmjwhen you are finished to return to the Waypoint List. OPERATION 3-26 . --a- 3. 7 Setting Alarms The NAV 398 has three operator programmable alarms that you can set to advise you when limits have been reached. The types of alarms available are: l ARRIVAL- Arrival at a waypoint. l OFF COURSE- Straying too far from track. Whenever an alarm is set and activated, the audible beeper will sound and the alarm characters will blink on-screen. You can set an Arrival alarm or Anchor alarm, but not both types together. Press the[CLEARlkey to silence the audio alarm. 3. 7. 1 The Arrival Alarm The Arrival alarm can be set to alert you when you are within a specified ARRlvAL , + w 9 wAyw'NT \ distance from your waypoint. The ar- CIRCLE ' J rivalalarmcanbesetErom0. 01 to9. 99 y l %@t%#E?rHEN \ , ARFUVAL CIRCLE nautical miles (run). !K To set an Arrival alarm: Press thel]key. Then enter the distance value for the desired arrival alarm zone with the numeric keys. [. . . ] Press and hold the In each case following the reset, the NAV 398 display changes to "Ent Lat" screen of the the Auto Start-up sequence and will prompt you to re-enter the Latitude and Longitude initial position coordinates. 4. 5 Troubleshooting Chart SYMPTOM No Power Input Not Receiving SNR readings = 0 CHECK Check in-line fuse. Re-enter if error of more than 2 degrees. Check position corrections for invalid entries. [. . . ]