User manual RAYMARINE RAYCHART 631

[. . . ] hsb2 PLUS Series Color LCDDisplay Owner's Handbook Document number: 81188_3 Date: September 2002 iii hsb2 PLUS Series Color LCD Display Owner's Handbook September 2002 INTENDED USE The display units detailed in this handbook may form part of navigational radar systems intended for light marine use. These displays and radar systems are only an aid to navigation. SAFETY NOTICES This radar equipment must be installed and operated in accordance with the instructions contained in this manual. Failure to do so can result in personal injury and/or navigational inaccuracies. The LCD display unit and scanner unit contain high voltages. [. . . ] You can place waypoints, using simulator mode, before you install the chartplotter on your vessel. Note: Radar marks may also be displayed on the screen if your chartplotter is a combined radar/chartplotter or is part of an integrated system; these are screen annotations - you cannot GOTO marks, nor include them in routes. When you place a new waypoint, it is displayed using the default symbol of a cross (unless you have changed the symbol in Chart Set Up). The waypoint is added to the waypoint list and tagged with the next available number. You can use the edit functions to change the symbol and name. When the cursor is positioned over a waypoint, the waypoint bearing and range are displayed. Waypoints in the current route are available on other SeaTalk instruments that support current route transfer, for example, anotherRaymarine Chartplotter or ST80 Masterview. You can transfer waypoints between the chartplotter and other NMEA or SeaTalk instruments using the Waypoint Transfer functions. You can also save waypoints to, or load them from, a user cartridge. These functions are described in Section 5. 6. This section explains how to perform the following tasks using the on-screen cursor and the waypoint list: · Placing a Waypoint · Selecting a Waypoint · Displaying Waypoint data · Editing a Waypoint (symbol, name & position) · Erasing a Waypoint Working with Waypoints Chapter 5: Standard Chart Operations 5-9 · Moving a Waypoint At the end is a section about using the ST60/80 Navigator Keypad to select, edit, and name your waypoints. Placing a Waypoint The scenario Place and Goto a Waypoint on page 2-26 provides a simple example of how to place a waypoint. To access the place waypoint soft keys, press MARKS: MARKS MARKS PLACE WPT PLACE WPT WAYPOINT LOAD/SAVE PLACE WPT PLACE WPT WAYPOINT AT CURSOR AT VESSEL LIST USER CARD AT CURSOR AT VESSEL LIST D5572-1 D4169-1 To place a waypoint at the cursor position or at the vessel position: PLACE WPT AT CURSOR PLACE WPT AT VESSEL 1. Press either the PLACE WPT AT CURSOR or the PLACE WPT AT VESSEL soft key. The waypoint is added to the waypoint list and tagged using the next available number. The waypoint soft keys are displayed until you move the cursor away from the waypoint or press CLEAR. GOTO WAYPOINT EDIT WAYPOINT ERASE WAYPOINT MOVE WAYPOINT D4163-1 You can use the EDIT WAYPOINT soft key to name the waypoint as described in Editing Waypoints below. Press CLEAR or ENTER to remove the place waypoint soft keys. To place a waypoint as latitude/longitude using the Waypoint List: MARKS 1. PressMA RKS, followed by the WAYPOINT LIST soft key. The Waypoint List and associated soft keys are displayed. Press the MAKE NEW WAYPOINT soft key followed by the LAT/LONG soft key; the WPT POSITION (LAT/LONG) screen is displayed, with it's associated soft keys. The waypoint is placed at the current vessel position, or if not available, the cursor position. WAYPOINT LIST MAKE NEW WAYPOINT Placing a Waypoint 5-10 hsb2 PLUS Series Color LCD Display WAYPOINT LIST SYMBOL NAME WAYPOINT 001 WAYPOINT 002 WAYPOINT 003 WAYPOINT 004 WAYPOINT 005 POSITION BRG _186° TEMP 50°21^966N 001°20^368W RNG _21. 0nm DEPTH TIME ---°C --/--/-- ---m --:--:-- Placing a Waypoint DATE GOTO WAYPOINT EDIT WAYPOINT MAKE NEW WAYPOINT WAYPOINT TRANSFER D4262-2 3. You can use the soft keys to edit the waypoint position as described in Editing the Waypoint Details on page 5-13. [. . . ] The Installed Warranty provides for onboard repair or exchange, by Raymarine or it's approved service agents, for a period of 2 years/24 months, from date of sale of the boat to the end user ­ where the equipment has been installed by a Raymarine certified installer, or from commissioning of the installation by a Raymarine certified installer, or 30 months from date of shipment of the equipment from Raymarine ­ whichever expires first, except as provided below. Obtaining Warranty Service In the event of Warranty service being required, contact Raymarine or the nearest Raymarine certified service agent ­ a full list of local service agents are available on the Internet or can be requested from the nearest Raymarine agent. A suitable proof of purchase, showing date, place of purchase, and serial number must be made available to Raymarine or authorized service agent at the time of request for Warranty service. In cases where a Raymarine certified installer has not installed the product; i. e. Limited Warranty, the affected unit must be returned to the local Raymarine approved service agent, with a copy of proof of purchase and/or completed warranty card. [. . . ]