User manual RAYMARINE ST8002 SMARTPILOT CONTROLLER

[. . . ] ST8002 SmartPilot Controller Operating Guide Document reference: 81271-1 Date: December 2005 Autohelm, HSB (High Speed Bus), SailPilot, SeaTalk and SportPilot are registered trademarks of Raymarine Ltd. Raymarine, AST (Advanced Steering Technology), AutoAdapt, AutoLearn, AutoRelease, AutoSeastate, AutoTack, AutoTrim, FastTrim, GyroPlus, RayGyro, RayPilot and WindTrim are trademarks of Raymarine Ltd. Raymarine and SeaTalk are trademarks of Raymarine Ltd Handbook contents © Raymarine Ltd. 2005. i Important Information About the documentation provided Welcome to Raymarine SmartPilot. [. . . ] Press disp or wait for 5 seconds to return to the previous display. Note: You will lose these temporary changes to response level whenever the system is powered off. You can make permanent adjustments in User Calibration (see page 23). 10 ST8002 SmartPilot Controller Operating Guide Off Course warning = deviation to port = deviation to starboard D4229-3 The SmartPilot warns you when you have been off course from the locked heading for longer than 20 seconds. It shows whether the deviation is to port or starboard. Note: The default off course angle is set at 20º. You can adjust this angle in Dealer Calibration (see SmartPilot Commissioning Guide). 1. To cancel the off course warning, press standby to return to manual steering. Check whether your boat is carrying too much sail, or whether the sails are badly balanced. You can usually significantly improve course keeping by improving the sail balance. Note: The SmartPilot also clears the warning if the heading recovers or if you change course. 1. 5 Can I adjust the display lighting & contrast? How do I adjust the lights? You can adjust the display and keypad lighting by: 1. Pressing disp for 1 second from any mode to access the LAMP screen and turn on the lights. Press the disp button to cycle through the possible illumination settings: LAMP 3 (the brightest setting), LAMP 2, LAMP 1, OFF, LAMP 1, LAMP 2, LAMP 3 and so on: · as you change the setting, the illumination on any other SeaTalk instruments or control units will also change. Chapter 1: SmartPilot Operation 11 1 second D5517-2 3. The display automatically returns to the previous mode if you do not press a button for 10 seconds: · if you press another mode button within 10 seconds you will select the mode assigned to that button (for example: auto selects Auto mode, standby selects Standby mode). Notes: (1) You can also adjust the lighting level from any other SeaTalk instrument or control unit. (2) When you switch off the unit you lose any changes you have made to the lighting level. How do I adjust the contrast? To set the display contrast level: 1. With the autopilot in Standby mode, press the disp button for one second to access the LAMP screen. Press the disp button for one second again, to display the CONTRAST screen. Use the up and down arrow buttons to set the required contrast level (from 1 to 15). The display automatically returns to the previous mode if you do not press a button for 10 seconds: Note: if you press another mode button within 10 seconds you will select the mode assigned to that button (for example: auto selects Auto mode, standby selects Standby mode). 12 ST8002 SmartPilot Controller Operating Guide Chapter 2: Advanced Operation 13 Chapter 2: Advanced Operation 2. 1 How do I follow a route set on a Chartplotter? CAUTION: Safety in Track mode Track mode provides accurate track keeping even in complex navigational situations. However, it is still the skipper's responsibility to ensure the safety of their boat at all times through careful navigation and frequent position checks. Track mode assists precise navigation and removes the tasks of compensating for wind and tidal drift. However, you MUST still maintain an accurate log with regular plots. In Track mode, the SmartPilot maintains a route between waypoints created on a navigation system. It makes any course changes necessary to keep your boat on course, automatically compensating for tidal streams and leeway. Track mode is available only if you have connected the SmartPilot to a suitable navigation system providing SeaTalk or NMEA information. (See SmartPilot Commissioning Guide for connection details) Your SmartPilot system can receive route information from: · a SeaTalk navigation instrument or chartplotter. · a navigation system transmitting data in NMEA 0183 format. How do I activate Track mode? CAUTION: Make suitable preparations for entering track mode When you enter Track mode, the SmartPilot will bring the boat onto the track in a controlled way. [. . . ] Software information The following illustration shows how to display the software information: · press and hold standby for 4 seconds: · after 2 seconds you will see the DISPLAY CAL screen · then after another 2 seconds you see controller software version · press disp to display the computer software version · press disp again to display the total number of hours the SmartPilot has been used in Auto mode. Software Information standby standby 4 seconds 1 second Time autopilot used in Auto Control unit software version 1 second Course computer software version 1 second D5494-2 Chapter 3: Fault Finding & Maintenance 31 Product details table For future reference, you may want to use this table to record serial and software information for your SmartPilot: Serial Number SmartPilot Controller SmartPilot Computer Hours Used hours Software Version 32 ST8002 SmartPilot Controller Operating Guide 33 Specifications ST8002 control unit Nominal supply voltage: Operating voltage range: Current consumption (in Standby mode) Operating temperature: Water protection: Overall dimensions: width height depth Keypad: Liquid Crystal Display (LCD): LCD illumination: Input connections: Output connections: CE approvals: 12 V DC via SeaTalk 10 V to 15 V DC 50 mA (less than 120 mA with full lighting) 0 °C to +70 °C (32 °F to 158 °F) waterproof to CFR46 175 mm (6. 9 in) 115 mm (4. 53 in) 54 mm (2. 13 in) 9 button illuminated keypad, with rotary control shows heading, locked course and navigational data, and up to 15 data pages 3 brightness levels + off; 15 contrast levels SeaTalk (x2) and NMEA 0183 SeaTalk (x2) conforms to: 89/336/EC (EMC), EN60945:1997 SmartPilot computer functions SmartPilot computer S1G, S2G and S3G systems · Internal GyroPlus yaw sensor · Enhanced course keeping using AST · FastTrim · Full access to AutoLearn, providing automatic steering calibration · Improved track-keeping · Steers to true and apparent wind in Wind Vane mode · Improved calibration access Non-G systems · Full basic functionality · Improved track-keeping · Steers to true and apparent wind in Wind Vane mode · Improved calibration access, but without AutoLearn · Uses Raymarine steering algorithm without AST · No FastTrim 34 ST8002 SmartPilot Controller Operating Guide Glossary Term AST Meaning Advanced Steering Technology (AST) is Raymarine's unique advanced steering algorithm. It uses inputs from a wide variety of sensors to tune the autopilot's operation to provide superior control of the boat in any condition. Self-learning calibration feature available on S1G, S2G and S3G autopilot systems. The AutoTrim setting determines the rate at which the autopilot applies `standing helm' to correct for trim changes caused by varying wind loads on the sails or superstructure. [. . . ]