User manual RENKUS-HEINZ COBRANET

[. . . ] CobraNetTM User's Manual CobraNetTM User's Manual 19201 Cook Street, Foothill Ranch, CA 92610-3501 USA Phone: (949) 588-9997 Fax: (949) 588-9514 Email: sales@renkus-heinz. com Web: www. renkus-heinz. com CobraNetTM is a registered trademark of Peak Audio, Broomfield, Colorado 722-RH 419 REV A 1 CobraNetTM User's Manual Table of Contents Safety Instructions Introduction What is CobraNet System Design CobraNet Hardware Input/Output Connections Unit Identification Software CNDisco. exe (CobraNet Discovery Program) CobraNet. exe R-Control with CobraNet R-Control and CobraNet Combiner Box 3 4 4 4 5 5 6 7 7 9 12 12 2 722-RH 419 REV A CobraNetTM User's Manual Cautions CAUTION TO AVOID ELECTRIC SHOCK, DO NOT INSERT FINGERS OR OBJECTS INTO ANY OPENINGS IN Sicherheitsvorschriften VORSICHT UM ELEKTRISCHEN SCHLAG ZU VERMEIDEN, KEINE FINGER ODER GEGENSTÄNDE IN ÖFFNUNNGEN DES GEHÄUSES STECKENN WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE WARNUNG: ZUR VERMEIDUNG VON FEUER ODER ELEKRISCHEN SCHLÄGEN DAS GERÄT NICHT MIT REGEN Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the use to the presence of uninsulated "dangerous Voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans. Erklärung der graphischen Symbole Der Blitz mit nach untenzielendem Pfeil in einem gleichseitigen Dreieck weist den Benutzer auf das Vorhandensein einer unisolierten, "gefährlichen Spannung" im Gehäuse hin, die stark genug sein kann, einer Person einen gefährlichen elektrischen Schlag zu versetzen. The exclamanation point, within an equilateral triangle is intended to alert the users to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. Das Ausrufezeichen in einem gleichseitigen Dreieck weist den Benutzer auf wichtige Betriebs- und Wartungsvorschriften in den beiliegenden Unterlagen des Gerätes hin. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN VORSICHT GEFAHR EINES ELEKTRISCHEN SCHLAGES NICHT ÖFFNEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL VORSICHT!UM DAS RISIKO EINES ELEKTRISCHEN SCHLAGES ZU VERMINDERN, ABDECKUNG NICHT ENTFERNEN. KEINE BENUTZER BEDIENUNG-STEILE IM INNERN. [. . . ] It's also used for setting the IP addresses and updating a device's firmware. IP address assignment: The CobraNet Discovery program will automatically assign the IP address to the CobraNet devices. By allowing the CobraNet Discovery program to automatically assign the IP address, you will be assured that there will not be any conflicts between two CobraNet devices having the same IP address. To set up the automatic IP address assignment, use the following procedure. In the IP Address Range box, uncheck the Enable Auto Assignment check box. Set the Start IP address for the desired IP address range. Set the End IP address for the desired IP address range. Check the Enable Auto Assignment check box. Once the automatic IP address assignment has been configured, any devices added to the network will be assigned a unique IP address in the range specified. Updating firmware: If it is required to update the firmware to the CobraNet unit, this is accomplished by using the CobraNet Discovery program. To update the firmware, use the following procedure. In the Database Location box, you need to set the path to the location of the new firmware. You can either type in the path or use the Browser button. The file you are looking for is called database. ini. Select OK to close the Configuration window. In the main CobraNet Discovery window, select the CobraNet device on which you wish to upgrade the firmware. Under the CobraNet menu, select Update Firmware. The Select Firmware Version screen will appear. Select the desired firmware and push the Update button. It will then ask if you are sure if you want to update the firmware, select OK. Once the update has been completed, you may need to reboot the CobraNet board. 722-RH 419 REV A 7 CobraNetTM User's Manual CNDisco. exe (CobraNet Discovery) (Cont. ) Main Window: The main window of the CobraNet Discovery program will display all the CobraNet devices located on the CobraNet network. [. . . ] Of these 32 possible channels, the unit is capable of outputting 2 of these channels simultaneously. The Input Selection section of the software allows you to select these 2 channels. Analog Inputs: This indicates where the analog audio channels are coming from. The Speaker Monitor path routs audio from the individual speaker amplifier outputs onto the CobraNet network. [. . . ]