User manual REVEL M8 REV 0

[. . . ] · Position each speaker so that the tweeter is approximately at ear level. · Generally, bass output will increase as the speaker is moved closer to a wall or corner. · Refer to the "Home Theater" section if you also plan to use the speakers for home theater reproduction. Left Front Channel Right Front Channel Subwoofer Listening Position Left Surround Channel Left Surround Channel Center Surround Channel Right Surround Channel Right Surround Channel Figure 2: This overhead view shows a typical home theater plan. Left/right rear channels are for a 7-channel system. [. . . ] Doing so will cause poor imaging and diminished bass response. Be certain that positive and negative wire strands are completely isolated to avoid short circuits that may damage your equipment. Step One Place bracket against the wall and mark the positions on the wall where you would like to place the mounting screws. Step Two Place the bracket against the wall and fasten three 1-1/2", #10 wood screws through the bracket's screw holes into the wall. If a wall stud is not available, use an appropriate anchor. Step Three Remove rear foot, place the speaker on the bracket and insert the provided 1/4"-20 screw through the bottom of the bracket into the threaded insert on the bottom of the satellite (Figure 3). Turn satellite to desired angle and tighten. ­ + Figure 4: Wiring diagram shows polarity connections for one channel of an audio or home theater system. (wall) (Remove foot) (Insert screw through bracket into speaker) Figure 3: Bracket on wall. 4 Operation Surround Modes When using the system in a Dolby® Digital or DTS® home theater system, make sure the receiver or processor is set to "Small" for all M8 loudspeakers. Some receivers/processors offer a choice of crossover frequencies. Select 110Hz as the crossover frequency for all M8 loudspeakers in the system. Some Dolby Digital-equipped receivers/processors offer different setup options for each source or surround mode, e. g. , CD-stereo, DVD, Dolby, Pro Logic. ® In each case, follow your equipment's instructions to ensure that the subwoofer output is turned on and that the speakers are set to "Small" or to a crossover frequency of 110Hz in each mode. Maintenance and Service The satellite enclosure may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. All wiring connections should be inspected and cleaned or remade periodically. The frequency of maintenance depends on the metals involved in the connections, atmospheric conditions and other factors, but once per year is the minimum. If a problem occurs, make sure that all connections are properly made and clean. If a problem exists in one loudspeaker, reverse the connection wires to the left and right speakers. If the problem remains in the same speaker, then the fault is with the loudspeaker. If the problem appears in the opposite speaker, the cause is in another component or cable. If your M8 loudspeaker should ever need service, please contact your local dealer or distributor, or visit www. revelspeakers. com for the location of a service center. 5 Specifications Revel® ConcertaTM M8 Frequency Response (±3dB) Recommended Amplifier Power Range Sensitivity (2. 83V @ 1m, 2 anechoic) Nominal Impedance Crossover Frequency Low-Frequency Drivers LF Extension High-Frequency Driver External Dimensions (H x W x D) Weight (Net) 110Hz ­ 21kHz 10 ­ 125 Watts 88dB 8 Ohms 2-Way high-order at 2. 2kHz Dual 3" (76mm) woofers with Micro Ceramic Composite (MCC) cones ­3dB @ 110Hz, ­6dB @ 100Hz, ­10dB @ 90Hz 1" (25mm) tweeter with waveguide and Micro Ceramic Composite (MCC) dome 11-5/8" x 4-1/4" x 4-1/2" (296mm x 107mm x 113mm) 3. 45 lb (1. 6kg) 4. 20 4. 45 4. 45 11. 64 Declaration of Conformity We, Harman Consumer Group, Inc. 2, route de Tours 72500 Château du Loir France declare in own responsibility that the product described in this owner's manual is in compliance with technical standards: 2. 8 EN 61000-6-3:2001 EN 61000-6-1:2001 4. 5 2. 6 Laurent Rault Harman Consumer Group, Inc. Château du Loir, France 8/08 6 Limited Warranty A valid serial number is required for warranty coverage. This Revel warranty protects the original retail purchaser for a period of five (5) years (parts and labor) from any failure as a result of original manufacturing defects, so long as: 1. The Revel products were purchased within the 50 United States, its territories or Canada. The dealer from whom the Revel products were purchased was authorized to sell such products at the time of the original purchase. The original, dated Bill of Sale is presented whenever service is required during the warranty period. The balance of this warranty is transferable only if the used product is purchased from an authorized Revel dealer. [. . . ] This warranty is applicable in the United States, its territories and Canada. Outside of the United States, its territories and Canada, please contact an authorized Revel dealer for warranty and service information. The information this document contains is subject to change without notice. In the event that there are differences between this warranty and the provisions of any advertisements, documentation, product brochures or packaging cartons, the terms of this warranty will prevail. [. . . ]