User manual REX OZ23

[. . . ] · Filtri antigrasso metallici · Metal antigrease filters · Filtri al carbone attivo · Activated carbon filters · Illuminazione · Light · Pulizia · Cleaning 11 20 11 20 11 20 3 Part 1 - INSTALLATION INSTRUCTIONS 1 - GENERAL DATA This hood has been designed to be wall-mounted above a cooking hob with one side resting against a wall. It works either by suction (external outlet) or filter (internal recycling). Because of the complexity and weight of the hood, its installation should be carried out by qualified staff, taking care to respect all local regulations on air discharge. The manufacturer cannot be found liable for any damage due to improper installation. 2 - COMPONENTS The cooker hood is made up of the following components (fig. [. . . ] 2 - Air discharge towards the wall S07_02 (fig. 3) In this case the hood can only be used in suction mode. In this case the hood can only be used in suction mode. S07_04 G 2b 3 R R 14 4a 4b S07_03 Part 1 - INSTALLATION INSTRUCTIONS 4. 2 - Installation of the hood canopy C 1 - Drilling the wall a) Using the cardboard template provided, mark on the wall the centres of holes 1 for fixing of the hood canopy C. The centre of hole 2 for fixing the chimney, (fig. 5a) air outlet directed upwards or towards the wall, (fig. 5b-c) air outlet to the right or left hand side, must be marked at a distance X from the line between holes 1, obtained by measuring the extension Z of the chimney required for installation, plus 18 mm X=Z+25-7. Using a Ø8 mm drill bit, drill the points marked in this way. 5a 5b 5c 50 ø1 0 7 ø1 2 105 105 2 Z X 2 1 1 1 2 1 1 1 39 100 100 ø8 650 b) When installed with the air outlet directed towards the wall (fig. 5a), it will be necessary to drill an air ducting opening, measuring Ø120 or 150 mm, 6 according to the diameter of the S 2 1 flange F provided. 2 - Fitting the fixing elements a) Insert the rawl plugs provided V 4 mm 7 4 into holes 1 and 2. O L= A08_07 b) Fit the eye bolts O (fig. c) Fix the wall bracket S in hole 2 using the screw V provided (fig. · Air outlet directed to the right or left hand side (fig. - Remove the four screws fastening the plastic frame, as shown in fig. 19) and replace the four screws removed as above. 3 - Fixing the chimney a) Loosen the screws M fixing the two parts of the chimney and pull the inner section I (fig. b) Rest the lower section of the chimney in its housing on the top of the hood canopy. Lower the ducting fan unit until it reaches the wall bracket S and fix it using the screw H provided (fig. Fit the cover D (provided) 19 on the wall bracket S (fig. c) Fix the chimney A to the hood canopy C using the four screws provided (fig. d) Insert the transparent seal Q (provided), so as to eliminate any play between the two parts of the chimney (fig. e) Remove the support rod B. S07_16 17 18 R S07_19 I P S S H M A08_20 20 A08_21 21 22 D A08_22 E E E 24 E Q Q A08_24 18 A08_23 23 Part 1 - INSTALLATION INSTRUCTIONS 4. 4 - Ducting or recirculation fitting 1 - Ducting fitting. This is possible for all forms of installation: a) Connect the air outlet to the external ducting system. [. . . ] This gives an excellent ratio between treated air flow and noise level; BUTTON V3 = High speed, suitable to deal with heavy cooking fumes, even for long periods of time. 3 - MAINTENANCE Constant maintenance is a guarantee for long-lasting working order and efficiency. Special care should be taken of the metal antigrease filter and activated carbon filter (for filter hoods only). 20 Part 2 - USE AND MAINTENANCE INSTRUCTIONS 3. 1 - Metal antigrease filters 1 - Cleaning It is necessary to wash these filters at least every two months with a normal detergent; their compact size enables them to be washed also in dishwasher. 2 - Replacement Remove the metal grease filter by removing the filter retaining clips (fig. 29). 29 S36_29 3. 2 - Activated carbon filters 1 - How they work The activated carbon filter can hold odours until it reaches total saturation. [. . . ]