User manual RICOH AFICIO AP600N AP600N QUICK INSTALL GUIDE

[. . . ] The recommended (or minimum) space requirement is as follows: Check the contents of the box according to the following list. If one or some items are missing, please contact your sales or service representative. 120V, 60Hz, 8. 4A or more The printer's location should be carefully chosen because environmental conditions greatly affect its performance. Connect the power cord to a power source with the following specifications: UNPACKING THE PRINTER AND CHECKING THE CONTENTS OF THE BOX INSTALLING THE TONER CARTRIDGE Place the toner cartridge on a flat surface. Pull out the tape inside the unit horizontally while holding the cartridge with one hand as shown in the illustration. INSTALLING THE PAPER TRAY The default paper settings size are as follows: Metric version: A4 L (long-edge feed) Inch version: 81/2" x 11" L (long-edge feed) For settings other than the default paper size, see "Loading Paper and Other Media" in the Printer Reference provided as a PDF file on the CD-ROM labeled "Operating Instructions". For more information about the paper sizes that can be set in the paper tray, see "Paper and Other Media Supported by this Printer" in the Printer Reference provided as a PDF file on the CD-ROM labeled "Operating Instructions". [. . . ] Do not shake the cartridge. Important Do not expose the toner cartridge to a light for a long time. If you do, the toner cartridge will be damaged and the print quality might be reduced. \ Optimum Environmental Conditions Recommended temperature and humidity %RH 10°C 80% 80 15°C 70% 27°C 80% 25°C 70% Remove the plastic bag. Lift the printer and move it to the place where you want to install it. When lifting the machine, use the inset grips on both sides. Otherwise the machine could break or cause injury if dropped. Open the front cover by pushing the front cover release button. Holding the grips of the toner cartridge, insert it into the printer until it stops. ZKGH160E Note Do not touch the three white pins on the left front side of the printer. 60 32°C 54% 40 15°C 30% 10°C 15% 10 20 25°C 30% 32°C 15% 30 °C While lifting the front side of the tray, pull it out of the printer. 20 ZKGH126E %RH 80 50°F 80% 59°F 70% 80. 6°F 80% 77°F 70% 89. 6°F 54% Remove the fixing material inserted between toner cartridge and the printer. ZKGT121E ZKGT052N Remove the orange adhesive tape (7 pieces). 60 Insert the toner cartridge in its appropriate position by gently pushing down. ZKGH170E 40 59°F 30% 50°F 15% 50 60 70 77°F 30% 89. 6°F 15% 80 90 °F 20 Load paper into the paper tray with the print side up. Possible operation range Recommended range The machine must be level within 5 mm, 0. 2" both front to rear and left to right. ZKGT146E While lifting the front side of the toner cartridge, pull it out of the printer. ZKGT145E Environments to Avoid Close the front cover. Important Locations exposed to direct sunlight or strong light Dusty areas Areas with corrosive gases Areas excessively cold, hot, or humid ZKGH180E Important Confirm that the top of the stack is not higher than the limit mark inside the tray. Confirm that the paper fits under the rear guide. Locations near an air conditioner or humidifier Locations near other electronic equipment Locations where the printer might be subjected to frequent strong vibration ZKGT115E Note Do not hold the toner cartridge upside down or stand it vertically. Do not put the toner cartridge on an unstable or tilted surface. ZKGH135E Important Do not close the front cover with force. If you cannot close the cover easily, pull out the toner cartridge from the printer and insert it again. After that, close the front cover again. Note Caution · When you pull the plug out of the socket, grip the plug to avoid damaging the cord and causing a fire or an electric shock. · It is dangerous to handle the plug with wet hands. An electric shock might occur. Press the {L} or {M} key until the language you want to select appears on the panel display. Press the {Enter } key. Turn off the power switch. When loading paper other than A4 L (long-edge feed) or 81/2" x 11" L (long-edge feed), adjust the paper size dial to match the size and feed direction of the paper in the paper tray. CONNECTING THE POWER CORD Press the {Enter } key. CONNECTING THE PRINTER TO A COMPUTER Network connection Parallel connection Important The parallel interface cable is not provided with the printer. Make sure that the interface cable you use is appropriate for your computer. The printer's parallel connection is a standard bi-directional interface. It requires a standard 36-pin parallel cable compliant with IEEE 1284 and an available parallel port on your computer. To avoid electrical interference, use a shielded cable. USB connection Important The USB interface cable is not provided with the printer. Make sure that the USB interface cable you use is appropriate for your computer. Loop the network interface cable and attach the ferrite core. Note Check that the power switch is turned off. Press the {On Line} key. The settings are applied and the ready message appears on the panel display. ZKGH200E The network interface cable loop should be about 15 cm(6")( ) from the end of the cable (on the end closet to the printer). The ferrite core at the end of the cable should be a ring type ferrite core. Attach the USB interface cable to the USB interface connector of the printer. Secure the cable. When you load paper lager than A4 K (short-edge feed) or 81/2" x 11" K (short-edge feed), you should extend the tray. For more information, see "Paper and Other Media Supported by this Printer" in the Printer Reference provided as a PDF file on the CD-ROM labeled "Operating Instructions". Note Do not use a parallel cable more than 2. 5 meters (8. 2 feet) long. Turn off the power switch. Carefully slide the paper tray into the printer until it stops. ZKGH205E Securely insert the power cord plug into the wall socket. PRINTING A CONFIGURATION PAGE You can check if the printer works properly by printing a configuration page. [. . . ] If you want to use the English panel display, the following procedures are unnecessary. Press the {Menu} key. "Menu" appears on the panel display. ZKGT290E Press the {L} or {M} key until the following message appears on the panel display. Connect the other end of the network interface cable to the network. Turn on the power switch. Check the LEDs on the ethernet port. ZKGX115E Menu: List/Test Print Press the {Enter } key. Attach the other end of the interface cable to the interface connector of the computer. Secure the cable. SETTING UP FOR PRINTING Check that the power switch is turned on. The following message appears on the panel display. Important Rating voltage of the parallel interface connector for the computer ; Max. DC5V. Press the {Menu} key. On Line Menu List/Test Print: Config. P/Er. Log Press the {L} or {M} key until the following message appears on the panel display. Printing requires installation of a printer driver for the operating system. [. . . ]