User manual RICOH AP206

[. . . ] QUICK INSTALLATION GUIDE<G063-8935> Please read the Safety Information in the "Printer Reference" before using this machine. It contains important information related to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS. 220-240 V, 50/60 Hz, 6 A or more Caution · Do not incinerate the oil bottle. This action could cause a fire or a personal injury. If oil is spilt, wipe it up with an alkaline cleaner. [. . . ] : Printing is possible in simplex printing, and also in duplex printing (if duplex printing is allowed). Limitation Duplex printing is not allowed with A5, Com#10 Env, DL Env, 8. 5 × 13, 8. 25 × 13, 8 × 13, and Custom Size paper. 113 Appendix Low Memory The error message shown below is output by the printer whenever there is not enough memory to print your data. There is not enough memory in your printer to print this page. Change print quality in the printer driver and try again. For details, please refer to the troubleshooting section in your manual. The following are the actions you should take when you encounter memory shortage problems. If these actions do not solve the problem individually, try them in combination with each other. Install the optional memory unit to increase the amount of printer memory . Reference For more information about how to install the optional memory unit, see the "Setup Guide" that comes with the printer. 6 B C For more information about kinds of optional memory units, see P. 118 "Options". With the IPDL-C printer driver: On the [Print Quality] tab, select [Custom] and click [Setting/Change]. With the RICOH-SCRIPT2 printer driver: Set the resolution to 300dpi. Use the printer's "System Menu" to turn on "Image Memory". P. 90 "System Menu" 114 Moving and Transporting the Printer Moving and Transporting the Printer R CAUTION: · It is recommended that at least two persons are used to lift the printer. Otherwise, the printer might fall and cause personal injury. · When lifting the machine, use the grips on both sides. The machine could break or cause an injury if dropped. · Before moving the machine, unplug the power cord from the outlet. If the cord is unplugged abruptly, it could become damaged. Damaged plugs or cords can cause an electrical or fire hazard. · When you pull out the plug from the socket, grip the plug to avoid damaging the cord and causing a fire or an electric shock. · When moving the printer, be sure to keep it level to avoid spilling the fuser oil. If oil is spilt, wipe it with alkaline cleaner. Otherwise, the oily surfaces can create the danger of slipping and personal injury. Important Be sure to disconnect all cables from the printer before transporting it. The printer is a precision piece of machinery. Take care to avoid damage during shipment. 6 115 Appendix Specifications Mainframe Configuration: Desktop Print process: Laser beam and dry toner electrical photographic system Printing speed: Monochrome: 24 pages per minute Color: 6 pages per minute (A4, 81/2"×11") Resolution: 600 dpi 6 Parallel interface: Interface Standard 36-pin printer cable and a parallel port on the host computer IEEE 1284-B I/F (Compatible, Nibble, ECP) · Do not use a cable more than 2. 5 meters (8. 2 feet) long. Printer language: IPDL-C, RICOH-SCRIPT2 Paper size: P. 21 "Paper and Other Media Supported by This Printer" Paper weight: P. 21 "Paper and Other Media Supported by This Printer" Power source: Inside of the front cover of this manual Power consumption: Standby (Maximum) Printing (Maximum) Printing (Average) Energy Saver (Maximum) 1, 350 W or less 1, 350 W or less 600 W or less 35 W or less 116 Specifications Noise emission *1 Sound power level During printing Stand-by 62 dB (A) 57 dB (A) Sound pressure level *2 During printing Stand-by *1 *2 49 dB (A) 44 dB (A) The above measurements made in accordance with ISO 7779 are actual value. It is measured at the position of the operator. Dimensions: Width Printer only With optional Paper Feed Unit With optional paper feed unit and optional Paper Cassette With Optional paper feed unit and optional duplex unit With optional paper feed unit, optional Paper Cassette and optional duplex unit 500 mm (19. 7") 500 mm (19. 7") 500 mm (19. 7") Depth 520 mm (20. 5") 520 mm (20. 5") 592 mm (23. 3") Height 410 mm (16. 1") 555 mm (21. 9") 555 mm (21. 9") 6 500 mm (19. 7") 605 mm (23. 8") 605 mm (23. 8") 500 mm (19. 7") 677 mm (26. 7") 605 mm (23. 8") Measurement conditions: With the paper tray opened. Weight: Approximately 39 kg (86 lb) (including consumables) Warm-up time: Less than 240 seconds (20°C, 68°F) Paper capacity: Standard paper tray Optional paper feed unit *1 250 sheets *1 500 sheets *1 Paper weight: 80 g/m2, 20 lb Paper output capacity: 250 sheets (80 g/m2, 20 lb) 117 Appendix CPU: RM5261-250 MHz Memory: Standard 32 MB, up to 256 MB (with the optional SDRAM module) Network (an optional Network Interface Board required): Topology: Ethernet (10BASE-T/100BASE-TX) Protocol: TCP/IP, IPX/SPX, NetBEUI, AppleTalk Optional equipment: · PAPER FEED UNIT Type206 · Paper Cassette Type204 (Legal) · AD390 (duplex unit) · Network Interface Board Type306 · Memory Unit Type B 32MB · Memory Unit Type B 64MB · Memory Unit Type B 128MB 6 Options PAPER FEED UNIT Type206 Paper size: P. 21 "Paper and Other Media Supported by This Printer" Paper weight: P. 21 "Paper and Other Media Supported by This Printer" Paper Cassette Type204 (Legal) Paper size: P. 21 "Paper and Other Media Supported by This Printer" Paper weight: P. 21 "Paper and Other Media Supported by This Printer" 118 Specifications Network Interface Board Type306 Topology: Ethernet (10BASE-T/100BASE-TX) Protocols: TCP/IP, IPX/SPX, NetBEUI, AppleTalk Interface connector: RJ45 Required cable: STP (Shielded Twisted-Pair) cable Category/Type5 or better *A cable is not enclosed with this option. Memory Unit Type B (32MB/64MB/128MB) Memory type: SD (Synchronous Dynamic) RAM Number of pins: 144 pins Access time: PC100 6 119 Appendix Consumables R CAUTION: · Our products are engineered to meet the highest standards of quality and functionality. [. . . ] /usr/lib/lpadmin -Pnp -v/dev/null -mrmodel -ormnphost -orplp -ob3 · np is the printer name, nphost is the host name. C Set the printer so that the print job is listed in the print queue. /usr/lib/accept np D Set the printer to perform the print job. /usr/lib/enable np E Restart the scheduler. [. . . ]