User manual RICOH FW870

[. . . ] INMIMI FW870 Operating Instructions I In accordance I for the main switch: with ISO Standard 7001, this machine uses the following-- symbols 0 Q) I means POWER ON. I I For good copy quality, Ricoh recommends Ricoh shall not be responsible for any damage or expense that may result from the use of parts other than genuine Ricoh parts in your Ricoh office product. I Note: Some illustrations may be slightly different from your machine. 1 115 V, 60 HZ, 12A Power Source: Please make sure to connect the power cord to a power source as above. For details about po wer connection, see paqe xx. @ Copyright 1996, Ricoh Co. , Ltd. Note to users in the United States of America Warning: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] The copier starts copying. Do not release the original until it is fed into the copier. 18 COPYING PARTIAL COPYING The Partial Copy function copies only a part of an original. This function specifies the start and end points in the original feed direction. S The Partial Copy function cannot apply to originals having a length of less than 245 mm, 9. 6" in the paper feed direction. S The Partial Copy function cannot be used in the rear table. S The Partial Copy function cannot be used when the Sample Copy function is selected. S The start and end points cannot be set within 162 mm, 6. 4" from the leading edge of paper. S The spacing between the start and end points is 100 mm, 4. 0" at the minimum. S Roll paper is cut in 250 mm, 9. 9" at the minimum. 1 Press the Partial Copy key. The indicator on the Partial Copy key blinks. When you press the Partial Copy key again, the leading edge of an original becomes the start point for partial copying. When you press the Partial Copy key for the third time, you can cancel partial copying. 2 Set your original. The copier starts copying. Do not release the original until it is fed into the copier. COPYING 19 PARTIAL COPYING 3 Press the Partial Copy key when the leading edge of the area to be copied comes to the position where it is covered with the original table cover. The indicator on the Partial Copy key lights. If you do not press the Partial Copy key, the original is delivered without partial copying. Original feed direction 4 Press the Partial Copy key when the trailing edge of the area to be copied comes to the position where it is covered with the original table cover. The indicator on the Partial Copy key goes off. If you do not specify the trailing edge, the copier will do the following: · Cuts the paper automatically according to the original length when the synchro cut function is selected. · Otherwise, cuts the paper in the specified length. · The area to be copied might differ slightly from the desired one depending on the timing of pressing the key. Original feed direction 20 COPYING SAMPLE COPYING The Sample Copy function copies an original in 245 mm, 9. 6" from its leading edge in the paper feed direction. This allows you to check the copy condition of the current settings in advance. 1 Press the Sample Copy key. The indicator on the Sample Copy key is lit. When you press the Sample Copy key again, you can cancel sample copying. 2 Set your original. Do not release the original until it is fed into the copier. 3 The copier starts copying. COPYING 21 PAPER TYPE/ROLL WIDTH ENTRY FUNCTION This function allows you to store the paper type and roll width for a selected paper feeder. When you change the paper feeder to the specified one, the paper type and roll width are set to the stored values. 1 Press the Paper Select key until your desired paper feeder indicator blinks. The roll paper width is displayed in the paper cut length indicator. You can press the Clear Modes key to cancel the indication. 2 Press the Paper Select key to select the paper feeder. 3 Press the Paper Size key to select the roll paper width. When you select "Manual Feed" for the paper feeder, you cannot specify the paper size. 4 To use the New-ABCDE-size paper, select "New size" using the + and - keys. When the paper feeder indicator blinks for "New size", the 24, 18, 12, and 9 indicators are lit. 22 COPYING PAPER TYPE/ROLL WIDTH ENTRY FUNCTION 5 Press the Fusing Temperature key to select the paper type. 6 Press the Enter key. The above settings are stored. If you do not want to store the settings, press the Clear Modes key. COPYING 23 USING THE PROGRAM FUNCTION The Program function allows you to store a collection of copy settings as programs 1 to 9 and switch them as needed. Programming a Collection of Copy Settings 1 Press the Program key. The indicator on the Program key blinks. The copy counter displays the current program number. 2 Use the and keys to select a program number for which you store copy settings. You cannot change settings in Program No. Each time you make a copy, the copy settings are stored in Program No. you press the Clear/ Stop key, Program No. 0 is selected. When 3 Press the Enter key. The indicator on the Program key blinks. 24 COPYING USING THE PROGRAM FUNCTION 4 Specify values for each setting. You can store the following settings with the Program function. For the way to specify values, see the corresponding pages. · Sample copying See page 21. · Partial copying (The start and end points cannot be stored) See page 19. [. . . ] If the floor or base is slant, you cannot make copies properly. The copier must be level within 5 mm both front to rear and left to right. If the copier is not stabilized, it might cause a fault as well as a danger to users. S Avoid a location subject to vibrations, such as near a factory. [. . . ]