User manual RICOH MP7083A

[. . . ] NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installlation. [. . . ] Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) 5. 25-inch half height bay required +5V/+12V power socket required CD-R(74min): Ricoh, Mitsubishi Chemical, Taiyo Yuden, Mitsui Chemicals, TDK and Maxell discs CD-R(80min): Ricoh, Taiyo Yuden, TDK discs CD-RW: Ricoh and Mitsubishi Chemical discs*2 High Speed CD-RW: Ricoh discs *2 CPU Memory Harddisk Interface Drive bay Power Recommendation discs*3 *1 *2 *3 abCD does not support these Operating System. The disc written using the CD-R/RW drive may not be readable by CD-ROM drives. Multi-read compatible (Random UDF compatible) drives are necessary. Even if it is the recommendation disc, some of discs may have possibility to fail writting with highest writting speed with the problem on the disc. In this case, please try to write with lower writting speed, or please try to use another disc. Multi-read compatible (Random UDF compatible) drives are: q q Drives that can read low reflectivity discs. Drives that support Packet Write. Front Panel Rear panel Front Panel 1. Disc tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. Caution Don't use force to pull out or push in the disc tray. This might cause damage to the loading section of the drive. 2. Headphone jack This jack is for connecting headphones or mini-speakers. 3. Volume control This is used to adjust the output volume of the headphone jack. It can't be used to adjust the output volume for the audio output connectors on the rear panel. Caution Turn the volume down before turning on the power. Sudden loud noises can damage your hearing. 4. Busy indicator This indicator lights green when a disc is mounted into the drive. When the disc is being accessed, it flashes or lights green. If a disc is not mounted, the indicator does not light even when the power is turned on. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 5. Eject button This is the button used to eject or insert in the disc tray. 6. Emergency eject hole This drive has a function that allows the disc to be ejected manually if this becomes necessary in an emergency such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. Using it excessively will cause malfunction. Rear panel 1. Analog Audio Output Connector Provides output to a sound card (Analog signal). 2. Jumper Connector This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. 3. IDE Interface Connector Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. Caution Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. 4. Power Connector Connects to the power supply (5 and 12V DC) of the host computer. Caution Be careful to connect with the proper way. [. . . ] Replacing the Computer Cover When the installation of the drive unit is complete, replace the computer cover. Back 1. Device Drivers When using Windows 98/95, Window NT Workstation Ver. 4. 0, Windows 2000 (Professional) the installation of any special device drivers are not required. In order to ensure normal drive operation or if the drive is not recognized by your computer, please check the following: In order to ensure normal drive operation If the drive is not recognized by your computer In order to ensure normal drive operation For Windows 98/95 Users q q The drive is displayed in [control panels] - [system] - [device manager] - [CD-ROM] 32-bit is displayed in [control panels] - [system] - [performance] For Windows NT Workstation Ver. 4. 0 Users q The drive is displayed on the IDE controller in [control panels] - [SCSI adapter] -[devices] For Windows 2000 (Professional) Users q The drive is displayed in [control panels] - [system] - [hardware] - [device manager] If the drive is not recognized by your computer For Windows 98/95 Users q If a [?] indicator is displayed on the IDE controller in [control panels] - [system] -[devices manager]-[harddisk controler], you will need to contact your PC manufacturer or the motherboard manufac-turer and get the appropriate IDE controller driver. For Windows NT Workstation Ver. 4. 0 Users q If a [?] indicator is displayed on the IDE controller in [control panels] - [SCSI adapter] -[devices] , you will need to contact your PC manufacturer or the motherboard manufacturer and get the appropriate E-IDE controller driver. For Windows 2000 (Professional) Users q If a [?] indicator is displayed on the IDE controller in [control panels] - [system] [hardware] - [device manager] , you will need to contact your PC manufacturer or the motherboard manufacturer and get the appropriate E-IDE controller driver. Back 1. [. . . ]