User manual RICOH MP7320A

[. . . ] NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Enhanced-IDE (ATAPI) model Compliant with industry standard Orange Book Part II (CD-R) and Part III (CD-RW). Can read not only CD-R and CD-RW media, but also video CDs, music CDs, photo CDs*1, and CD-Text Can read data at 40x speed (6. 0MB/sec data transfer rate), write data at 32x speed (CD-R, 4. 8MB/sec data transfer rate. ) and write data at 10x speed *2(High Speed CD-RW, 1. 5MB/sec data transfer rate). The recorded CD-RW media can be played in a DVD player or a multi-read CD-ROM Player, maintaining future compatibility. Supports random UDF for easy writing to CD-RW media. Offers the Optimum Write Speed Control function UDMA-capable *1 Bundled software does not support this writing format. *2 The speed at which to write on the current standard CD-RW media is 4x recording (at a data transfer rate of 600KB/second). q q q q q q q q q q q Explains the system environment required for using the drive as a CD-R/CD-RW drive. PC Operating System IBM PC/AT compatible Windows Me/98/98SE/95(ORS2 or later) Windows NT Workstation Ver. 4. 0 (Service Pack 5) or later Windows 2000 (Professional) Windows XP*1 Pentium 166 MHz or higher (When using JustLink) 64MB or more Hard disk with average access time of 19msec or less, and data transfer speed of 2, 500KB/sec or greater. Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) 5. 25-inch half height bay required +5V/+12V power socket required Recommendation Tested to be compatible Taiyo Yuden, Mitsui Chemicals, Mitsubishi CD-R Ricoh Chemical, Maxell CD-RW Ricoh Mitsubishi Chemical*2 High Speed CD-RW Ricoh Mitsubishi Chemical CPU Memory Hard disk Interface Drive bay Power Recommendation media*3 *1 *2 *3 For information on Windows XP supports, visit Ricoh's Web site The media written using the CD-R/RW drive may not be readable by CD-ROM drives. Multi-read compatible (Random UDF compatible) drives are necessary. Even if it is the recommendation disc, some of discs may have possibility to fail writing with highest writing speed with the problem on the disc. In this case, please try to write with lower writing speed, or please try to use another disc. Multi-read compatible (Random UDF compatible) drives are: q q Drives that can read low reflectivity discs. Drives that support Packet Write. Front Panel Rear panel Front Panel 1. Disc tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. Caution Don't use force to pull out or push in the disc tray. This might cause damage to the loading section of the drive. 2. Headphone jack This jack is for connecting headphones or mini-speakers. 3. Volume control This is used to adjust the output volume of the headphone jack. It can't be used to adjust the output volume for the audio output connectors on the rear panel. Caution Turn the volume down before turning on the power. Sudden loud noises can damage your hearing. 4. Busy indicator The indicator stays green when the medium is being accessed or being read. Or, it stays red during the writing time, or stays orange when the drive is in the wait state. 5. Eject button This is the button used to eject or insert in the disc tray. 6. Emergency eject hole This drive has a function that allows the disc to be ejected manually if this becomes necessary in an emergency such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. Using it excessively will cause malfunction. Rear panel 1. Digital Audio Output Connector Provides output to a sound card (Digital signal). * No dedicated digital audio cable is supplied with the MP7320A. 2. Analog Audio Output Connector Provides output to a sound card (Analog signal). 3. Jumper Connector This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. 4. IDE Interface Connector Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. Caution Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. Caution Be careful to connect with the proper way. [. . . ] Slave drive (Other IDE drive) To Install as a Slave Drive To install the drive as a Slave, change the jumper setting on the rear panel. Master drive (Other IDE drive) Back 1. Sound Card Connection If the computer has a sound card, the drive can be connected to the sound card with an audio cable. Make sure the connections are oriented so that L corresponds to L and R to R. [. . . ]