User manual RICOH MP9200A

[. . . ] NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installlation. [. . . ] UDMA-capable *1 Bundled software does not support this writing format. *2 The speed at which to write on the current standard CD-RW discs is 4x recording (at a data transfer rate of 600KB/second). q q q q q q q q q q Explains the system environment required for using the drive as a CD-R/CD-RW drive. PC Operating System IBM PC/AT compatible Windows Me/98/95(ORS2 or later) Windows NT Workstation Ver. 4. 0 (Service Pack 5) or later Windows 2000 (Professional) Pentium 166 MHz or higher (When using JustLink) 64MB or more Hard disk with average access time of 19msec or less, and data transfer speed of 1, 200KB/sec or greater. Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) 5. 25-inch half height bay required +5V/+12V power socket required discs*2 Recommendation Tested to be compatible Taiyo Yuden, Mitsui Chemicals, Mitsubishi CD-R Ricoh Chemical, Maxell CD-RW Ricoh Mitsubishi Chemical*1 High Speed CD-RW Ricoh Mitsubishi Chemical CPU Memory Hard disk Interface Drive bay Power Recommendation *1 *2 The disc written using the CD-R/RW drive may not be readable by CD-ROM drives. Multi-read compatible (Random UDF compatible) drives are necessary. Even if it is the recommendation disc, some of discs may have possibility to fail writing with highest writing speed with the problem on the disc. In this case, please try to write with lower writing speed, or please try to use another disc. Multi-read compatible (Random UDF compatible) drives are: q q Drives that can read low reflectivity discs. Drives that support Packet Write. Front Panel Rear panel Front Panel 1. Disc tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. Caution Don't use force to pull out or push in the disc tray. This might cause damage to the loading section of the drive. 2. Headphone jack This jack is for connecting headphones or mini-speakers. 3. Volume control This is used to adjust the output volume of the headphone jack. It can't be used to adjust the output volume for the audio output connectors on the rear panel. Caution Turn the volume down before turning on the power. Sudden loud noises can damage your hearing. 4. Busy indicator This indicator lights orange when a disc is mounted into the drive. When the disc is being accessed, it flashes or lights orange. If a disc is not mounted, the indicator does not light even when the power is turned on. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 5. Eject button This is the button used to eject or insert in the disc tray. 6. Emergency eject hole This drive has a function that allows the disc to be ejected manually for an emergency case such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. When the disc tray is in the ejected position, dust and other debris will enter, possibly causing read errors, write errors, or drive failure. Back Load the disc Emergency Eject Next Disc ejection Using the Drive in a Vertical Position Load the disc 1. Place the disc on the disc tray. Be careful not to touch the recording surface of the disc. 3. Load the disc by pressing the eject button or by lightly pushing in the disc tray. Next Load the disc Emergency Eject Disc ejection Using the Drive in a Vertical Position Using the Drive in a Vertical Position The drive can be installed in a vertical position. [. . . ] As long as the sound board comes with S/PDIF input, it can be connected externally to the D/A converter. The drive can be used as a CD transporter for playing CDs at the desired sound quality level. 1. Digital audio output terminal * Please purchase a digital-audio-capable sound board and a cable at additional cost. Replacing the Computer Cover When the installation of the drive unit is complete, replace the computer cover. Back 1. [. . . ]