User manual RICOH RCP40

[. . . ] Network Printing Guide Windows 95/98/Me Configuration Windows 2000 Configuration Windows XP Configuration Windows NT 4. 0 Configuration NetWare Configuration Macintosh Configuration Appendix For safe and correct use of this machine, please be sure to read the Safety Information in the Operating Instructions that comes with the machine before you use it. Introduction To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine. Important Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine. [. . . ] When you have finished the above steps, make sure that the queues are assigned. 5 O Press the {ESC} key until "Exit?" appears, and select [Yes] to exit PCON} SOLE. P Start the print server by typing the following from the console of the NetWare Server. If it is running, restart it after exiting it. To exit CAREE: unload pserver To start CAREE: load pserver print_server_name Note If the machine works as configured, "Waiting for job" appears. 61 NetWare Configuration NetWare 4. x, 5/5. 1 - Advanced Settings The actual procedures for configuring the machine vary depending on whether the Network Interface Board is configured as a print server or as a remote printer. This section describes how to configure it in the NetWare 4. x, 5/5. 1 environment. To use NetWare 5/5. 1 · If you use Pure IP, configure the machine to use the TCP/IP protocol. For more information about how to make the settings, see Printer Reference 1. 5 Preparation The following procedures use the Property Sheet method in configuring the Network Interface Board. If you configure the Network Interface Board as a NetWare print server for the first time, we recommend you use the Wizard method. See p. 53 "Quick Setup Using the NIB Setup Tool Wizard". Note This section assumes NetWare is functional and that the necessary environment for the NetWare Print Service is available. You should install the client software released from Novell in Windows before running the NIB Setup Tool for configuring in NDS mode or using Windows NT 4. 0. 62 NetWare 4. x, 5/5. 1 - Advanced Settings Setting Up as a Print Server Important You can set up the print server using the NDS or Bindery mode in NetWare 4. x, 5/5. 1. The following procedure is for setting up the print server using the NDS mode in NetWare 4. 1. When you set up the print server using the Bindery mode, use the NIB Setup Tool Wizard. See p. 53 "Quick Setup Using the NIB Setup Tool Wizard". Note If you use Pure IP in NetWare 5/5. 1, follow the procedure on p. 65 "Using Pure IP in the NetWare 5/5. 1 environment". A Log on to the file server as an Admin or an Admin equivalent. B Run the NIB Setup Tool. Reference p. 52 "Running the NIB Setup Tool" 5 C Click [Property Sheet] and click [OK]. The [NIB Setup Tool - Network board list] dialog box of the Network Interface Board appears. D Click [IPX protocol]. E Click the IPX address of the Network Interface Board which is to be configured, and then click [Next >]. Note If you do not know which Network Interface Board you are configuring, see the system configuration list to check the MAC address (Network Address). F Make sure that the MAC address and IPX address are correct, and click [Finish]. The [NIB Setup Tool] window appears. G Click [Configure]. The property sheet appears. H Click the [General] tab, and type the name of the print server into the [Device Name] box. I Click the [NetWare] tab, and make the following settings. A In the [Print Sever Name:] box, type the name of the print sever. 63 NetWare Configuration B In the [File Sever Name:] box, type the name of the file sever in which a print server is to be created. Click [Browse] to select a file server among those listed in the [Browse] dialog box. C In the [NDS Context:] box, type the context in which the print server is to be created. Click [Browse] to select a context among those listed in the [Browse] dialog box. As a context, object names are typed from a lower object and divided by a period. For example, if you want to create a print server into NET under DS, type "NET. DS". 5 D Click [OK] to close the property sheet. E After the confirmation dialog box appears, click [OK]. J On the [NIB] menu, click [Exit] to exit the NIB Setup Tool. K From Windows, run NWAdmin. Reference For more information about NWAdmin, see the documentation that comes with the NetWare. L Create a print queue as follows: A Select the container object the print queue is located in among those in the directory tree, and click [Create] on the [Object] menu. B In the [Class of new object] box, click "Print Queue", and click [OK]. [. . . ] msh> wins primary IPaddress msh> wins secondary IPaddress 7 Note To confirm the current configuration, use the show command. D Log off from telnet. E Restart the machine. Using DHCP You can use the machine under a DHCP environment. You can also register the printer NetBIOS name on a WINS server when it is running. Note Printers that register their NetBIOS name on a WINS server must be configured for the WINS server. Supported DHCP servers are Windows NT 4. 0 Server Service Pack 4 or later, Windows 2000 Server and NetWare 5. If you do not use WINS server, reserve machine's IP address in DHCP server so that the same IP address is assigned every time. 117 Appendix DHCP relay-agent is not supported. [. . . ]