User manual ROBLIN CUBE 600 MURALE

[. . . ] Poser la hotte sur les support muraux et fixer solidement le support de hotte au plafond à l'aide de 8 tiges filetées Ø 10 mm. Thank you for buying a ROBLIN product which has been manufactured to the highest quality standards to meet your requirements. We recommend you carefully read this booklet in which you will find instructions for installation, hints for use and maintenance. The Instructions for Use apply to several versions of this appliance. [. . . ] Wherever possible use rigid circular pipe which has a smooth interior, rather than the expanding concertina type ducting. The above assumes our 150 mm (6 INS) ducting is being installed. Please note ducting components and ducting kits are optional accessories and have to be ordered, they are not automatically supplied with the chimney hood. Place the anti-backflow flats item 8 over the round outlet item 6 and connect the ducting 150mm (6 INS) over the round outlet on top of the canopy and secure the connections with appropriate clamping rings or adhesive tape (Fig. Before fitting the chimney to the canopy make the electrical connection as described in the section titled ELECTRICAL. When the electrical connection has been made, test the lights and the fan motor. Fit the recirculation spigot R onto the upper chimney wall bracket using the same fixing screws (Fig. Connect the ducting 150mm (6 INS) not provided between motors item 6 and the recirculation spigot and secure the connections with appropriate clamping rings or adhesive tape. Before fitting the chimney to the canopy make the electrical connection as described in the section titled ELECTRICAL. When the electrical connection has been made, test the lights and the fan motor. Insert the charcoal filter into the base of the motor housing and secure the filter with two metal securing straps item A as illustrated in Fig. To use the cooker hood in the recycling mode re-programme the hood as follows: Starting in the recycling mode (the contaminated air passes into the hood through the grease filters and the purifying activated charcoal filter and back out into the kitchen through grilles). Press the `+' button (while the motor and lights are switched `OFF') until the five LED lights will flash twice to indicate confirmation that the cooker hood is in the recycling mode. reverting to the extraction mode (The cooker hood is ducted to the outside). Press the `+' button (while the motor and lights are switched `OFF') until the five LED lights will flash once to indicate confirmation that the cooker hood is in the extraction mode. B - BASIC INSTRUCTIONS Lighting Press LED button 1 to switch `ON' the lights and the LED will illuminate to confirm the lights are switched `ON'. Motor Press LED button 2 to switch `ON' the fan motor (and adjust the speed of the fan motor by pressing the LED button `+' and `-`) and the LED lights 2, 3 and 4 will illuminate. The fan speed will be increased if constant pressure is kept on the (+) button. LED 2 : Minimum speed - cooking with one pan or simmering LED 2 & 3 : Medium speed - normal cooking with up to 4 pans LED 2, 3 & 4 : Maximum speed - frying and cooking foods with strong odours Press LED button 5 to obtain the boost position for maximum effect and the LED will illuminate to confirm fan is switched `ON'. c - COMPLEMENTARY INSTRUCTIONS · Boost speed : To obtain the best performance it is advisable to switch `ON' the cooker hood a few minutes (in the boost setting) before you start cooking. to program the complementary function , proceed as follows: - Press LED button 2 to switch `ON' the fan motor and adjust the speed of the fan by pressing the LED button `+' and `-`. You should keep applying pressure to the `+' and `-` button until the required speed is selected. [. . . ] These batteries must be disposed of properly and could explode if damaged or exposed to heat. In the event of any malfunction or anomaly, notify your fitter who will have to check the appliance and its connection. In the event of damage to the mains supply cable, this can only be replaced by at approved repair centre appointed by the manufacturer who will have the required tools and equipment to carry out any repairs properly. Repairs carried out by other persons will invalidate the guarantee. [. . . ]