User manual ROBLIN LINEAR 1500 CENTRALE DIMENSIONS

[. . . ] The ducting system for this cooker hood must not be connected to any existing ventilation system, which is being used for any other purposes or to a mechanically controlled ventilation ducting. The ducting used must be made from fire retardant materials and the correct diameter must be used, as incorrect sized ducting will affect the performance of this cooker hood. When the cooker hood is used in conjunction with other appliances supplied with energy other than electricity, the negative pressure in the room must not exceed 0. 04 mbar to prevent the fumes from combustion being drawn back into the room. [. . . ] Fix the deflector using the M4 x 12 screws provided as illustrated in fig. 4 - Remove the grease filter cassettes and fix the charcoal filter retaining bracket onto the underside of the casing using the two 4. To use the cooker hood in the recycling mode re-programme the hood as follows: Starting in the recycling mode (the contaminated air passes into the hood through the grease filters and The purifying activated charcoal filter and back out into the kitchen through grilles). Press the `+' button (while the motor and lights are switched `OFF') until the five LED lights will flash twice to indicate confirmation that the cooker hood is in the recycling mode. reverting to the extraction mode (The cooker hood is ducted to the outside). Press the `+' button (while the motor and lights are switched `OFF') until the five LED lights will flash once to indicate confirmation that the cooker hood is in the extraction mode. B - BASIC INSTRUCTIONS Lighting Press LED button 1 to switch `ON' the lights and the LED will illuminate to confirm the lights are switched `ON'. Motor Press LED button 2 to switch `ON' the fan motor (and adjust the speed of the fan motor by pressing the LED button `+' and `-`) and the LED lights 2, 3 and 4 will illuminate. The fan speed will be increased if constant pressure is kept on the (+) button. LED 2 : Minimum speed - cooking with one pan or simmering LED 2 & 3 : Medium speed - normal cooking with up to 4 pans LED 2, 3 & 4 : Maximum speed - frying and cooking foods with strong odours Press LED button 5 to obtain the boost position for maximum effect and the LED will illuminate to confirm fan is switched `ON'. c - COMPLEMENTARY INSTRUCTIONS · Boost speed : To obtain the best performance it is advisable to switch `ON' the cooker hood a few minutes (in the boost setting) before you start cooking. These batteries must be disposed of properly and could explode if damaged or exposed to heat. Setup Process Modification: How to adjust the internal microprocessor data to suit the type of motor fitted to this appliance and the supply frequency of 50 or 60 Hz. 3 - Reconnect the mains supply while pushing the button 0/1 MOTOR for at least 2 seconds. 4 - Release the button 0/1 MOTOR (the Leds flash for about 3 seconds : capacity's confirmation SETUP PROCESS). 5 - While the LED is flashing select the motor type used while pushing one of the 5 buttons in accordance with the following: BUTTON 0/1 Light : Motor EBM PRO 220-240 V AC 50 Hz / 220 V AC 60 Hz. : If you have not selected a motor type while the LED is flashing the microprocessor will automatically select the default motor EBM PRO 220 - 240 V AC 50 Hz / 220 V AC 60 Hz. To obtain the best performance it is advisable to switch `ON' the cooker hood a few minutes (in the boost setting) before you start cooking and you should leave it running for approximately 15 minutes after finishing. Do not leave frying pans unattended during use as over-heated fat and oil might catch fire. Do not leave naked flames under this cooker hood. Ensure heating areas on your hotplate are covered with pots and pans when using the hotplate and cooker hood simultaneously. Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. [. . . ] In the event of damage to the mains supply cable, this can only be replaced by at approved repair centre appointed by the manufacturer who have the necessary tools and equipment to carry out any repairs properly. Repairs carried out by other persons will invalidate the guarantee. Should these warnings fail to be observed it could affect the safety of your cooker hood. When ordering spare parts quote the model number and serial number written on the rating plate, which is found on the casing behind the grease filters inside the hood. [. . . ]