User manual ROCKTRON JUICEEXTRACTOR

[. . . ] Care should be taken so that objects do not fall and liquids are not spilled into the unit through any openings. The power cord should be unplugged from the outlet when left unused for a long period of time. DO NOT ATTEMPT TO SERVICE THIS EQUIPMENT. THIS EQUIPMENT SHOULD BE SERVICED BY QUALIFIED PERSONNEL ONLY. [. . . ] The post-MID BANDWIDTH parameter determines (in octaves) the width of the selected mid band. The post-TREBLE LEVEL parameter allows you to cut or boost the high-band frequencies by 15dB after the distortion stage. The post-TREBLE FREQUENCY parameter allows you to select a high-band center frequency between 1KHz and 8KHz to be cut or boosted via the post-TREBLE LEVEL parameter. The post-TREBLE BANDWIDTH parameter determines (in octaves) the width of the selected high band. The post-PRESENCE LEVEL parameter allows you to cut or boost another high-band frequency by 15dB after the distortion stage. The post-PRESENCE FREQUENCY parameter allows you to select a high-band center frequency between 2KHz and 8KHz to be cut or boosted via the post-PRESENCE LEVEL parameter. The post-PRESENCE BANDWIDTH parameter determines (in octaves) the width of the selected high band. BASS FREQ BASS BW MID LVL MID FREQ MID BW TREBLE LVL TREBL FRQ TREBLE BW PRESENCE LVL PRES FREQ PRES BW 19 COMPRESSOR Function The COMPRESSOR function is available only in configurations which display "L-GAIN" in the configuration title. This function allows you to compress the signal prior to the distortion stage. Compression is often used to maintain an even level when using clean tones, and also to increase sustain when using distorted tones. The PARAMETER SELECT control will allow you to access these COMPRESSOR parameters: COMPRESSOR I/O The COMPRESSOR IN/OUT parameter determines whether the compressor is active for the current preset. The COMPRESSOR THRESHOLD parameter determines the input level (in dB) at which compression will begin. Lower settings of this parameter will result in more compression. The RATE parameter deterrnines the speed at which the phase shifted signal is modulated. The RESONANCE parameter adds feedback to the Phaser so that it has a more pronounced effect. The STAGES parameter determines how many stages of phase shift are to be active. A parameter setting of "4" produces a result similar to a vintage Phase 90, while a setting of "6" emulates other phaser pedals. DEPTH RATE RESONANCE STAGES 23 FLANGER Function The FLANGER function is available only in configurations displaying "FLAN" in the configuration title. Flanging involves splitting the input signal into at least two individual delayed signals (Voice 1 and Voice 2), then modulating these delayed signals so that, when summed back with the direct signal, phase cancellations will occur at some frequencies while peaks in the response will occur at others. The PARAMETER SELECT control will allow you to access these FLANGER parameters: FLANGER I/O The FLANGER I/O parameter determines whether the Flanger is active or bypassed for the current preset. The LEVEL 1 parameter determines the volume of Voice 1 relative to Voice 2. Tip: Keep the settings of these levels high and use the DIR/EFF mix parameter in the Mixer function to control the overall amount of flanged signal. PAN 1 The PAN 1 parameter allows you to pan Voice 1 to the left or right channel. The DEPTH 1 parameter adjusts the amount of modulation of Voice 1. Lower DEPTH settings produce more subtle effects, while higher settings will result in a more drastic effect. The RATE 1 parameter determines the speed at which Voice 1 is modulated. [. . . ] Any number of errors other than "0" means that the Voodu ValveTM may not have initialized properly and the process should be repeated. ERRORS 0 The Voodu ValveTM will remain in this condition until the FUNCTION SELECT control is turned to exit the Factory Restore function. The preset currently recalled will be the preset most recently restored into the current location. Restoring the Voodu ValveTM controller assignments: The controller assignments for the Voodu Valve can also be reinitialized without affecting presets and other stored information. Reinitialization of the controller assignments is necessary when setting up the Voodu Valve to operate in remote mode with a Rocktron All Access footswitch. To reinitialize only the controller assignments, enter a code number of "221" at Step 3 on the opposite page. 97 Selecting a Power On Preset The Voodu Valve allows you to store a Power On preset which will always be recalled when the unit is turned on. 2 1 3 Step 1 Turn the PRESET control to the preset number you wish to be recalled each time the unit is turned on. PRESS RECALL FOR Ö 34 PRESET TITLE Step 2 Recall the selected preset by pressing the RECALL button. 34 PRESET TITLE Step 3 Press the STORE button while viewing the preset number and title to save it as the Power On preset. PWR ON PR STORED 98 Using the Voodu Valve with a Rocktron All Access in REMOTE mode A Rocktron All Access MIDI footswitch can act as a dedicated remote control for the Voodu Valve - allowing direct access to specific Voodu Valve features and parameters from the footswitch at any time. Step 1 To use an All AccessTM footswitch as a dedicated remote, connect the MIDI OUT of the All AccessTM to the REMOTE jack of the Voodu ValveTM using a 7-pin MIDI cable, as shown below. To set up the Voodu ValveTM for remote operation, do the following: Step 2 Reinitialize the controller assignments as shown earlier in this section under the heading "Restoring the Voodu ValveTM Controller Assignments". [. . . ]